Microduck Robot●microduck-robot.com
Tools

Servo torque calculator

Confirm the supply, then compare the joint load.

Joint and supply
Load and motion
cm
g
g
cm
s
Safety margin
Assumptions and limits

SO-101 values come from the official MuJoCo model of the arm, stretched out level: the mass the joint moves, where its centre of mass is, and the reach to the gripper.

Compare only specifications measured at this voltage. Performance at a lower voltage is not estimated. SO-101 presets start at 7.4 V; confirm your actual supply.

From the joint axis to the object held at the end.

About half the reach for an even arm; servos further out move it outwards.

Shorter is faster and needs more torque to speed up and stop.

Times the torque you need, compared with the servo's rated torque.

Torque this joint needs

Holding the arm level
Extra to speed up and stop
Total
With the safety margin

Which servo can carry it

    How the calculator works

    Find out how much torque a robot arm joint needs, with a safety margin, and which servo can carry it. Start from an SO-101 joint or enter your own arm.

    The worst case for a lifting joint is the arm stretched out level, because gravity then pulls at the full reach. The holding torque is the weight of the load times its reach plus the weight of the arm times the distance to its centre of mass.

    Moving takes more: the joint has to speed the arm up and slow it down again. The calculator assumes a 90° move that speeds up for the first half and slows down for the second, and adds the torque that needs.

    All torque thresholds use the total multiplied by your safety margin. At the selected specification voltage, demand up to rated torque passes this estimate. Above rated but no more than half stall torque is only an unverified short-duty candidate, not a continuous-duty recommendation; check the manufacturer’s duty cycle and thermal limits. Higher demand fails. The speed check uses 80% of no-load speed and does not model the loaded torque–speed curve.

    Results are estimates for one joint lifting against gravity; friction, gear backlash and cable drag are not included. Check the servo's own datasheet before you build.

    Servo data used
    ModelSupplyStall torqueRated torqueNo-load speedSource
    Feetech HD1910M7.4 V15 kg·cm3.7 kg·cm114 rpmFeetech HD-1910-C001 specification A/0 (2026-09-07), as quoted in the Luwu Dynamics Microduck Robot_hardware BOM
    Feetech STS3215-C0017.4 V19.5 kg·cm5 kg·cm52 rpmFeetech STS3215 product specification (translated datasheet)
    Feetech STS3215-C01812 V30 kg·cm10 kg·cm45 rpmRetailer torque/speed specification; Feetech electrical datasheet A/0 (2023-07-20) is available separately
    Feetech STS325012 V50 kg·cm16 kg·cm75 rpmOur STS3250 product listing
    DAMIAO DM-J4310-2EC24 V122 kg·cm35.7 kg·cm200 rpmOur DM-J4310 product listing (3.5 N·m rated, 12 N·m peak)
    RobStride 0248 V173 kg·cm61.2 kg·cm315 rpmOur RobStride 02 product listing (6 N·m rated, 17 N·m peak)
    Questions

    What is the difference between stall torque and rated torque?

    Stall torque is the most a servo can push before it stops turning, for a moment and at full current. Rated torque is what it can deliver continuously without overheating. Size a joint by the rated torque; the stall torque is the ceiling.

    How much safety margin should I use?

    1.5 is enough for slow, well-known loads. Use 2 when the load or the arm length may change, and 3 for fast moves or when the servo must hold a pose for a long time.

    How do I convert kg·cm to N·m?

    1 N·m is 10.2 kg·cm, so divide kg·cm by 10.2. For example, 19.5 kg·cm is about 1.9 N·m. The calculator shows both, plus oz·in.

    Why does the SO-101 shoulder need so much torque?

    It carries the whole arm, about 400 g with its centre of mass 23 cm out, plus the load 41 cm away. Fully stretched and level, that is about 10 kg·cm before any margin. Compare at your actual supply; using a 12 V specification requires matching 12 V-rated servos and supply, and does not establish continuous-duty capability.

    Contact us