Prepare assembly and calibration files
Check your declared robot setup and the matching calibration format before running hardware commands. A motor calibration file and an IMU calibration file serve different purposes.
Supported robot configurations
- SO-101 leader · LeRobot 0.7.0
- SO-101 follower · LeRobot 0.7.0
- Microduck UNO Q / V1.1
Collect the correct inputs
For SO-101, identify leader or follower, bus, port, motor IDs and gearing. Confirm use_degrees yourself: the calibration JSON does not declare that mode. For UNO Q, use the IMU-v2 file and the separate declaration of 15 physical servo IDs; the simulation has 14 joints.
Review a setup in three steps
- Choose the robot and add each bus. Check joint-to-ID mappings; the same ID may appear on different buses.
- Select the matching motor or IMU JSON locally. Correct malformed fields, missing joints and unconfirmed units.
- Read the missing-item report and versioned instructions before exporting a backup or command text.
Reports, backups and commands
Download the project, check report and declared configuration backup. Where supported, command text uses the fixed official version and POSIX or PowerShell quoting. Commands are shown for you to review and run separately.
Declarations are not hardware verification
This page neither scans IDs nor writes calibration. A structurally valid file does not prove physical zero, direction or limits. UNO Q IMU calibration is not a fifteen-servo calibration backup. Files are checked in the browser without upload.
Worked setup and calibration checks
These examples check declared configuration and file structure. Every supplied calibration file is synthetic and must not be used on a real robot.
Offline configuration checks do not verify physical hardware or safety. These synthetic reference cases are separate from the settings above. Import an example to check its inputs again; a saved verdict is not trusted.
The same IDs on two separate buses
Can leader and follower both use IDs 1–6?
Version baseline: Microduck rules 2026-11-12.2 · LeRobot 0.7.0
Inputs and steps
LeRobot 0.7.0; separate leader/follower buses on /dev/ttyACM0 and /dev/ttyACM1; IDs 1–6 on each; useDegrees=true; two synthetic calibration JSON files.
- Choose both SO-101 profiles with distinct bus names and serial paths. Keep each profile’s own gear ratios.
- Load the two synthetic files and explicitly confirm the planned degree mode; that mode is not stored in motor calibration JSON.
- Check both bus records, the degree/range units and the offline result before downloading the reference project.
Reference check result
No known configuration conflict
No known configuration conflict: identical IDs are allowed across separate buses. commandsReady is true for the declared example.
Inspect inputs and reference JSON
{
"inputs": {
"profileId": "so101-leader-v0.7.0",
"buses": [
{
"busId": "leader",
"profileId": "so101-leader-v0.7.0",
"port": "/dev/ttyACM0",
"robotId": "example_leader",
"version": "0.7.0",
"useDegrees": true,
"unitsConfirmed": true,
"motors": [
{
"joint": "shoulder_pan",
"id": 1,
"model": "sts3215",
"gearRatio": 191
},
{
"joint": "shoulder_lift",
"id": 2,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "elbow_flex",
"id": 3,
"model": "sts3215",
"gearRatio": 191
},
{
"joint": "wrist_flex",
"id": 4,
"model": "sts3215",
"gearRatio": 147
},
{
"joint": "wrist_roll",
"id": 5,
"model": "sts3215",
"gearRatio": 147
},
{
"joint": "gripper",
"id": 6,
"model": "sts3215",
"gearRatio": 147
}
],
"calibration": {
"shoulder_pan": {
"id": 1,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"shoulder_lift": {
"id": 2,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"elbow_flex": {
"id": 3,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_flex": {
"id": 4,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_roll": {
"id": 5,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"gripper": {
"id": 6,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
}
}
},
{
"busId": "follower",
"profileId": "so101-follower-v0.7.0",
"port": "/dev/ttyACM1",
"robotId": "example_follower",
"version": "0.7.0",
"useDegrees": true,
"unitsConfirmed": true,
"motors": [
{
"joint": "shoulder_pan",
"id": 1,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "shoulder_lift",
"id": 2,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "elbow_flex",
"id": 3,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_flex",
"id": 4,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_roll",
"id": 5,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "gripper",
"id": 6,
"model": "sts3215",
"gearRatio": 345
}
],
"calibration": {
"shoulder_pan": {
"id": 1,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"shoulder_lift": {
"id": 2,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"elbow_flex": {
"id": 3,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_flex": {
"id": 4,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_roll": {
"id": 5,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"gripper": {
"id": 6,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
}
}
}
],
"imuCalibration": null
},
"status": "no_known_conflict",
"findings": [],
"outputs": {
"buses": [
{
"busId": "leader",
"profileId": "so101-leader-v0.7.0",
"role": "leader",
"family": "so101",
"version": "0.7.0",
"port": "/dev/ttyACM0",
"robotId": "example_leader",
"declaredMotors": [
{
"joint": "shoulder_pan",
"id": 1,
"model": "sts3215",
"gearRatio": 191
},
{
"joint": "shoulder_lift",
"id": 2,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "elbow_flex",
"id": 3,
"model": "sts3215",
"gearRatio": 191
},
{
"joint": "wrist_flex",
"id": 4,
"model": "sts3215",
"gearRatio": 147
},
{
"joint": "wrist_roll",
"id": 5,
"model": "sts3215",
"gearRatio": 147
},
{
"joint": "gripper",
"id": 6,
"model": "sts3215",
"gearRatio": 147
}
],
"jointUnits": {
"shoulder_pan": "degrees",
"shoulder_lift": "degrees",
"elbow_flex": "degrees",
"wrist_flex": "degrees",
"wrist_roll": "degrees",
"gripper": "range_0_100"
},
"calibrationStatus": "configuration-checked",
"calibration": {
"shoulder_pan": {
"id": 1,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"shoulder_lift": {
"id": 2,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"elbow_flex": {
"id": 3,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_flex": {
"id": 4,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_roll": {
"id": 5,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"gripper": {
"id": 6,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
}
}
},
{
"busId": "follower",
"profileId": "so101-follower-v0.7.0",
"role": "follower",
"family": "so101",
"version": "0.7.0",
"port": "/dev/ttyACM1",
"robotId": "example_follower",
"declaredMotors": [
{
"joint": "shoulder_pan",
"id": 1,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "shoulder_lift",
"id": 2,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "elbow_flex",
"id": 3,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_flex",
"id": 4,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_roll",
"id": 5,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "gripper",
"id": 6,
"model": "sts3215",
"gearRatio": 345
}
],
"jointUnits": {
"shoulder_pan": "degrees",
"shoulder_lift": "degrees",
"elbow_flex": "degrees",
"wrist_flex": "degrees",
"wrist_roll": "degrees",
"gripper": "range_0_100"
},
"calibrationStatus": "configuration-checked",
"calibration": {
"shoulder_pan": {
"id": 1,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"shoulder_lift": {
"id": 2,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"elbow_flex": {
"id": 3,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_flex": {
"id": 4,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_roll": {
"id": 5,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"gripper": {
"id": 6,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
}
}
}
],
"commandsReady": true,
"imuStatus": "not-applicable",
"imuPhysicalPoseVerified": false,
"physicalChecks": [
"physical_zero",
"physical_direction",
"physical_travel",
"physical_firmware"
],
"manualChecklist": [
"manual_single_motor",
"manual_physical_calibration"
]
}
}
What this case does not establish
- The files contain invented offsets and ranges for format testing only. They are not real backups and must never be used to operate hardware.
- Ports are examples, and unit mode is a separate declaration. Physical zero, direction and limits still need the official calibration procedure.
Reference prepared:
Specification sources
The links below retain the technical sources’ original titles. Read each version and review date with the case assumptions.
- lerobot-calibration410c095eacc0011d998a73383eb94abed2715af0 · reviewed
- lerobot-so101410c095eacc0011d998a73383eb94abed2715af0 · reviewed
- lerobot-units410c095eacc0011d998a73383eb94abed2715af0 · reviewed
- lerobot-leader410c095eacc0011d998a73383eb94abed2715af0 · reviewed
A duplicated ID inside one bus
What happens when shoulder_pan and shoulder_lift both declare ID 1?
Version baseline: Microduck rules 2026-11-12.2 · LeRobot 0.7.0
Inputs and steps
SO-101 follower; one bus, LeRobot 0.7.0, confirmed degree mode and a synthetic calibration file. shoulder_lift is deliberately declared as ID 1.
- Start with the follower profile and its synthetic file.
- Set shoulder_lift to ID 1 and inspect duplicate_motor_id and motor_mapping.
- Restore shoulder_lift to ID 2 without changing the calibration fixture, then compare reports.
Reference check result
Cannot use this configuration
The original declaration is blocked and commandsReady is false.
Inspect inputs and reference JSON
{
"inputs": {
"profileId": "so101-follower-v0.7.0",
"buses": [
{
"busId": "follower",
"profileId": "so101-follower-v0.7.0",
"port": "/dev/ttyACM0",
"robotId": "example_follower",
"version": "0.7.0",
"useDegrees": true,
"unitsConfirmed": true,
"motors": [
{
"joint": "shoulder_pan",
"id": 1,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "shoulder_lift",
"id": 1,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "elbow_flex",
"id": 3,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_flex",
"id": 4,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_roll",
"id": 5,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "gripper",
"id": 6,
"model": "sts3215",
"gearRatio": 345
}
],
"calibration": {
"shoulder_pan": {
"id": 1,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"shoulder_lift": {
"id": 2,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"elbow_flex": {
"id": 3,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_flex": {
"id": 4,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_roll": {
"id": 5,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"gripper": {
"id": 6,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
}
}
}
],
"imuCalibration": null
},
"status": "blocked",
"findings": [
{
"code": "duplicate_motor_id",
"severity": "blocked",
"fieldPath": "buses.0.motors.1.id",
"messageKey": "duplicate_motor_id",
"details": {
"id": 1,
"bus": "follower"
},
"sourceRef": "lerobot-calibration"
},
{
"code": "motor_mapping",
"severity": "blocked",
"fieldPath": "buses.0.motors.1.id",
"messageKey": "motor_mapping",
"details": {
"joint": "shoulder_lift",
"id": 2
},
"sourceRef": "lerobot-calibration"
}
],
"outputs": {
"buses": [
{
"busId": "follower",
"profileId": "so101-follower-v0.7.0",
"role": "follower",
"family": "so101",
"version": "0.7.0",
"port": "/dev/ttyACM0",
"robotId": "example_follower",
"declaredMotors": [
{
"joint": "shoulder_pan",
"id": 1,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "shoulder_lift",
"id": 1,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "elbow_flex",
"id": 3,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_flex",
"id": 4,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_roll",
"id": 5,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "gripper",
"id": 6,
"model": "sts3215",
"gearRatio": 345
}
],
"jointUnits": {
"shoulder_pan": "degrees",
"shoulder_lift": "degrees",
"elbow_flex": "degrees",
"wrist_flex": "degrees",
"wrist_roll": "degrees",
"gripper": "range_0_100"
},
"calibrationStatus": "configuration-checked",
"calibration": {
"shoulder_pan": {
"id": 1,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"shoulder_lift": {
"id": 2,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"elbow_flex": {
"id": 3,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_flex": {
"id": 4,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_roll": {
"id": 5,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"gripper": {
"id": 6,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
}
}
}
],
"commandsReady": false,
"imuStatus": "not-applicable",
"imuPhysicalPoseVerified": false,
"physicalChecks": [
"physical_zero",
"physical_direction",
"physical_travel",
"physical_firmware"
],
"manualChecklist": [
"manual_single_motor",
"manual_physical_calibration"
]
}
}
Adjust and check again
Restoring ID 2 removes both declared conflicts; the corrected reference has no known configuration conflict.
No known configuration conflict
Inspect the adjusted reference JSON
{
"inputs": {
"profileId": "so101-follower-v0.7.0",
"buses": [
{
"busId": "follower",
"profileId": "so101-follower-v0.7.0",
"port": "/dev/ttyACM0",
"robotId": "example_follower",
"version": "0.7.0",
"useDegrees": true,
"unitsConfirmed": true,
"motors": [
{
"joint": "shoulder_pan",
"id": 1,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "shoulder_lift",
"id": 2,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "elbow_flex",
"id": 3,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_flex",
"id": 4,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_roll",
"id": 5,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "gripper",
"id": 6,
"model": "sts3215",
"gearRatio": 345
}
],
"calibration": {
"shoulder_pan": {
"id": 1,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"shoulder_lift": {
"id": 2,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"elbow_flex": {
"id": 3,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_flex": {
"id": 4,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_roll": {
"id": 5,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"gripper": {
"id": 6,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
}
}
}
],
"imuCalibration": null
},
"status": "no_known_conflict",
"findings": [],
"outputs": {
"buses": [
{
"busId": "follower",
"profileId": "so101-follower-v0.7.0",
"role": "follower",
"family": "so101",
"version": "0.7.0",
"port": "/dev/ttyACM0",
"robotId": "example_follower",
"declaredMotors": [
{
"joint": "shoulder_pan",
"id": 1,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "shoulder_lift",
"id": 2,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "elbow_flex",
"id": 3,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_flex",
"id": 4,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_roll",
"id": 5,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "gripper",
"id": 6,
"model": "sts3215",
"gearRatio": 345
}
],
"jointUnits": {
"shoulder_pan": "degrees",
"shoulder_lift": "degrees",
"elbow_flex": "degrees",
"wrist_flex": "degrees",
"wrist_roll": "degrees",
"gripper": "range_0_100"
},
"calibrationStatus": "configuration-checked",
"calibration": {
"shoulder_pan": {
"id": 1,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"shoulder_lift": {
"id": 2,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"elbow_flex": {
"id": 3,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_flex": {
"id": 4,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_roll": {
"id": 5,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"gripper": {
"id": 6,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
}
}
}
],
"commandsReady": true,
"imuStatus": "not-applicable",
"imuPhysicalPoseVerified": false,
"physicalChecks": [
"physical_zero",
"physical_direction",
"physical_travel",
"physical_firmware"
],
"manualChecklist": [
"manual_single_motor",
"manual_physical_calibration"
]
}
}
What this case does not establish
- The calibration fixture is synthetic. Do not use its offsets or ranges on hardware.
- Editing the declaration neither scans nor changes a servo ID and does not verify a physical calibration.
Reference prepared:
Specification sources
The links below retain the technical sources’ original titles. Read each version and review date with the case assumptions.
- lerobot-so101410c095eacc0011d998a73383eb94abed2715af0 · reviewed
- lerobot-calibration410c095eacc0011d998a73383eb94abed2715af0 · reviewed
- lerobot-units410c095eacc0011d998a73383eb94abed2715af0 · reviewed
An IMU file is not a motor calibration backup
Why does a valid IMU-v2 structure still need review?
Version baseline: Microduck rules 2026-11-12.2 · Microduck runtime 4ce3315c86190a632f4d75a2464a4ed31c9af69a · IMU offset format 2
Inputs and steps
Microduck UNO Q / V1.1; 15 declared servo IDs; synthetic IMU-v2 frame qmi-policy-body-offset-v2 with zero arrays and no measurement provenance.
- Keep all 15 physical IDs, including mouth ID 34. The simulation model has 14 joints.
- Inspect synthetic-imu-v2.json: version, frame, acc_offset_ms2 and gyro_zero_dps belong to the IMU format.
- Read imu_provenance and leave the result under review; do not invent measurement records to obtain a pass.
Reference check result
Needs review
The required fields are structurally valid, but provenance is missing. The report remains needs_review and imuPhysicalPoseVerified is false.
Inspect inputs and reference JSON
{
"inputs": {
"profileId": "microduck-unoq-v1.1",
"buses": [
{
"busId": "microduck-main",
"profileId": "microduck-unoq-v1.1",
"port": "",
"robotId": "microduck",
"version": "4ce3315c86190a632f4d75a2464a4ed31c9af69a",
"useDegrees": null,
"unitsConfirmed": false,
"motors": [
{
"joint": "left_hip_yaw",
"id": 10,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "left_hip_roll",
"id": 11,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "left_hip_pitch",
"id": 12,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "left_knee",
"id": 13,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "left_ankle",
"id": 14,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_hip_yaw",
"id": 20,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_hip_roll",
"id": 21,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_hip_pitch",
"id": 22,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_knee",
"id": 23,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_ankle",
"id": 24,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "neck_pitch",
"id": 30,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "head_pitch",
"id": 31,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "head_yaw",
"id": 32,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "head_roll",
"id": 33,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "mouth",
"id": 34,
"model": "hd1910m",
"gearRatio": null
}
],
"calibration": null
}
],
"imuCalibration": {
"version": 2,
"frame": "qmi-policy-body-offset-v2",
"acc_offset_ms2": [
0,
0,
0
],
"gyro_zero_dps": [
0,
0,
0
]
}
},
"status": "needs_review",
"findings": [
{
"code": "imu_provenance",
"severity": "needs_review",
"fieldPath": "imuCalibration",
"messageKey": "imu_provenance",
"details": {},
"sourceRef": "duck-imu"
}
],
"outputs": {
"buses": [
{
"busId": "microduck-main",
"profileId": "microduck-unoq-v1.1",
"role": "robot",
"family": "microduck",
"version": "4ce3315c86190a632f4d75a2464a4ed31c9af69a",
"port": "",
"robotId": "microduck",
"declaredMotors": [
{
"joint": "left_hip_yaw",
"id": 10,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "left_hip_roll",
"id": 11,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "left_hip_pitch",
"id": 12,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "left_knee",
"id": 13,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "left_ankle",
"id": 14,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_hip_yaw",
"id": 20,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_hip_roll",
"id": 21,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_hip_pitch",
"id": 22,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_knee",
"id": 23,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_ankle",
"id": 24,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "neck_pitch",
"id": 30,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "head_pitch",
"id": 31,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "head_yaw",
"id": 32,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "head_roll",
"id": 33,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "mouth",
"id": 34,
"model": "hd1910m",
"gearRatio": null
}
],
"jointUnits": {
"left_hip_yaw": "encoder_steps",
"left_hip_roll": "encoder_steps",
"left_hip_pitch": "encoder_steps",
"left_knee": "encoder_steps",
"left_ankle": "encoder_steps",
"right_hip_yaw": "encoder_steps",
"right_hip_roll": "encoder_steps",
"right_hip_pitch": "encoder_steps",
"right_knee": "encoder_steps",
"right_ankle": "encoder_steps",
"neck_pitch": "encoder_steps",
"head_pitch": "encoder_steps",
"head_yaw": "encoder_steps",
"head_roll": "encoder_steps",
"mouth": "encoder_steps"
},
"calibrationStatus": "not-applicable",
"calibration": null
}
],
"commandsReady": false,
"imuStatus": "configuration-checked",
"imuPhysicalPoseVerified": false,
"physicalChecks": [
"physical_zero",
"physical_direction",
"physical_travel",
"physical_firmware",
"imu_standing",
"servo_midpoint"
],
"manualChecklist": [
"manual_declared_ids",
"manual_midpoint",
"manual_imu_standing",
"manual_power"
]
}
}
What this case does not establish
- IMU-v2 does not contain the 15 motor calibrations and must not be presented as their backup.
- The zero arrays are synthetic. No stationary upright sampling, real pose or 15-servo/14-joint correspondence has been physically verified.
Reference prepared:
Specification sources
The links below retain the technical sources’ original titles. Read each version and review date with the case assumptions.
- duck-config4ce3315c86190a632f4d75a2464a4ed31c9af69a · reviewed
- duck-imu4ce3315c86190a632f4d75a2464a4ed31c9af69a · reviewed
- duck-midpoint4ce3315c86190a632f4d75a2464a4ed31c9af69a · reviewed