Microduck Robot●microduck-robot.com
ツール

組み立て・校正の事前確認

設定とファイルをローカルで確認します。実機の校正は未検証です。

ツールを読み込み中…

組み立てと校正ファイルの準備

ハードウェアのコマンドを実行する前に、申告した構成と対応ファイルを確認します。モーター校正とIMU校正は別の用途です。

対応ロボット構成

  • SO-101 leader · LeRobot 0.7.0
  • SO-101 follower · LeRobot 0.7.0
  • Microduck UNO Q / V1.1

ルール版: 2026-11-12.2

必要な入力を揃える

SO-101ではleader/follower、バス、ポート、ID、減速比を確認します。校正JSONに単位モードはないため、use_degreesを自分で確認してください。UNO QはIMU-v2と15個の実機サーボIDを別々に扱い、シミュレーションは14関節です。

組み立て確認の手順

  1. ロボットと各バスを選び、関節とIDの対応を確認します。異なるバスでは同じIDを使用できます。
  2. 対応するモーター/IMUのJSONを端末で選び、形式、欠けた関節、未確認の単位を修正します。
  3. 不足項目と固定版の手順を読んでからバックアップやコマンドを保存します。

報告とコマンド

プロジェクト、検査報告、申告した構成の控えをダウンロードできます。対応コマンドは固定の公式版とPOSIX/PowerShellの引用形式を使用します。内容を確認し、別途実行してください。

実機を確認した記録ではありません

IDのスキャンや校正の書き込みは行いません。形式が正しくても実機のゼロ点、方向、限界は証明できません。UNO QのIMU校正は15サーボの校正バックアップではありません。ファイルはブラウザー内で処理します。

組み立て・校正チェックの実例

申告した構成とファイル形式を確認する例です。付属の校正ファイルはすべて合成データであり、実機に使用しないでください。

ローカル確認は実機の動作や安全性を保証しません。 ここに示す合成ケースは、上のフォームに入力した値とは別の参考データです。ケースをインポートすると入力から再チェックされ、保存済みの判定はそのまま採用されません。

別のバスなら同じIDを使える

リーダーとフォロワーが両方ともID 1–6を使ってよいですか?

対象バージョン: Microduck rules 2026-11-12.2 · LeRobot 0.7.0

入力条件と手順

LeRobot 0.7.0。leader/followerは/dev/ttyACM0と/dev/ttyACM1の別バスで、各IDは1–6、useDegrees=true。校正JSONは2つとも合成データです。

  1. 両方のSO-101プロファイルを選び、バス名とポートを分けます。減速比は各プロファイルの値を使います。
  2. 合成ファイルを読み込み、予定する度単位を別途確認します。モーター校正JSON自体には単位モードがありません。
  3. 両バス、度/範囲の単位、オフライン結果を確認して参照プロジェクトを保存します。

参考ケースの確認結果

既知の構成矛盾なし

既知の構成矛盾はありません。別バス間では同じIDを使用でき、この申告例ではcommandsReadyがtrueです。

入力と参考結果のJSONを見る
{
  "inputs": {
    "profileId": "so101-leader-v0.7.0",
    "buses": [
      {
        "busId": "leader",
        "profileId": "so101-leader-v0.7.0",
        "port": "/dev/ttyACM0",
        "robotId": "example_leader",
        "version": "0.7.0",
        "useDegrees": true,
        "unitsConfirmed": true,
        "motors": [
          {
            "joint": "shoulder_pan",
            "id": 1,
            "model": "sts3215",
            "gearRatio": 191
          },
          {
            "joint": "shoulder_lift",
            "id": 2,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "elbow_flex",
            "id": 3,
            "model": "sts3215",
            "gearRatio": 191
          },
          {
            "joint": "wrist_flex",
            "id": 4,
            "model": "sts3215",
            "gearRatio": 147
          },
          {
            "joint": "wrist_roll",
            "id": 5,
            "model": "sts3215",
            "gearRatio": 147
          },
          {
            "joint": "gripper",
            "id": 6,
            "model": "sts3215",
            "gearRatio": 147
          }
        ],
        "calibration": {
          "shoulder_pan": {
            "id": 1,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "shoulder_lift": {
            "id": 2,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "elbow_flex": {
            "id": 3,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "wrist_flex": {
            "id": 4,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "wrist_roll": {
            "id": 5,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "gripper": {
            "id": 6,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          }
        }
      },
      {
        "busId": "follower",
        "profileId": "so101-follower-v0.7.0",
        "port": "/dev/ttyACM1",
        "robotId": "example_follower",
        "version": "0.7.0",
        "useDegrees": true,
        "unitsConfirmed": true,
        "motors": [
          {
            "joint": "shoulder_pan",
            "id": 1,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "shoulder_lift",
            "id": 2,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "elbow_flex",
            "id": 3,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "wrist_flex",
            "id": 4,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "wrist_roll",
            "id": 5,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "gripper",
            "id": 6,
            "model": "sts3215",
            "gearRatio": 345
          }
        ],
        "calibration": {
          "shoulder_pan": {
            "id": 1,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "shoulder_lift": {
            "id": 2,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "elbow_flex": {
            "id": 3,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "wrist_flex": {
            "id": 4,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "wrist_roll": {
            "id": 5,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "gripper": {
            "id": 6,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          }
        }
      }
    ],
    "imuCalibration": null
  },
  "status": "no_known_conflict",
  "findings": [],
  "outputs": {
    "buses": [
      {
        "busId": "leader",
        "profileId": "so101-leader-v0.7.0",
        "role": "leader",
        "family": "so101",
        "version": "0.7.0",
        "port": "/dev/ttyACM0",
        "robotId": "example_leader",
        "declaredMotors": [
          {
            "joint": "shoulder_pan",
            "id": 1,
            "model": "sts3215",
            "gearRatio": 191
          },
          {
            "joint": "shoulder_lift",
            "id": 2,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "elbow_flex",
            "id": 3,
            "model": "sts3215",
            "gearRatio": 191
          },
          {
            "joint": "wrist_flex",
            "id": 4,
            "model": "sts3215",
            "gearRatio": 147
          },
          {
            "joint": "wrist_roll",
            "id": 5,
            "model": "sts3215",
            "gearRatio": 147
          },
          {
            "joint": "gripper",
            "id": 6,
            "model": "sts3215",
            "gearRatio": 147
          }
        ],
        "jointUnits": {
          "shoulder_pan": "degrees",
          "shoulder_lift": "degrees",
          "elbow_flex": "degrees",
          "wrist_flex": "degrees",
          "wrist_roll": "degrees",
          "gripper": "range_0_100"
        },
        "calibrationStatus": "configuration-checked",
        "calibration": {
          "shoulder_pan": {
            "id": 1,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "shoulder_lift": {
            "id": 2,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "elbow_flex": {
            "id": 3,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "wrist_flex": {
            "id": 4,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "wrist_roll": {
            "id": 5,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "gripper": {
            "id": 6,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          }
        }
      },
      {
        "busId": "follower",
        "profileId": "so101-follower-v0.7.0",
        "role": "follower",
        "family": "so101",
        "version": "0.7.0",
        "port": "/dev/ttyACM1",
        "robotId": "example_follower",
        "declaredMotors": [
          {
            "joint": "shoulder_pan",
            "id": 1,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "shoulder_lift",
            "id": 2,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "elbow_flex",
            "id": 3,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "wrist_flex",
            "id": 4,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "wrist_roll",
            "id": 5,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "gripper",
            "id": 6,
            "model": "sts3215",
            "gearRatio": 345
          }
        ],
        "jointUnits": {
          "shoulder_pan": "degrees",
          "shoulder_lift": "degrees",
          "elbow_flex": "degrees",
          "wrist_flex": "degrees",
          "wrist_roll": "degrees",
          "gripper": "range_0_100"
        },
        "calibrationStatus": "configuration-checked",
        "calibration": {
          "shoulder_pan": {
            "id": 1,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "shoulder_lift": {
            "id": 2,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "elbow_flex": {
            "id": 3,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "wrist_flex": {
            "id": 4,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "wrist_roll": {
            "id": 5,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "gripper": {
            "id": 6,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          }
        }
      }
    ],
    "commandsReady": true,
    "imuStatus": "not-applicable",
    "imuPhysicalPoseVerified": false,
    "physicalChecks": [
      "physical_zero",
      "physical_direction",
      "physical_travel",
      "physical_firmware"
    ],
    "manualChecklist": [
      "manual_single_motor",
      "manual_physical_calibration"
    ]
  }
}

このケースでは確認できないこと

  • オフセットと範囲は形式検査用に作った値です。実機のバックアップではなく、ハードウェア制御には絶対に使わないでください。
  • ポートは例で、単位モードは別の申告です。実機のゼロ点・方向・限界は公式手順で校正する必要があります。

参考データの作成日:

仕様の出典

以下のリンクには技術資料の原題を記載しています。ケースの前提条件とあわせて、対象バージョンと確認日を確認してください。

  • lerobot-calibration410c095eacc0011d998a73383eb94abed2715af0 · 確認日
  • lerobot-so101410c095eacc0011d998a73383eb94abed2715af0 · 確認日
  • lerobot-units410c095eacc0011d998a73383eb94abed2715af0 · 確認日
  • lerobot-leader410c095eacc0011d998a73383eb94abed2715af0 · 確認日

同じバス内でIDが重複した場合

shoulder_panとshoulder_liftが両方ID 1だとどうなりますか?

対象バージョン: Microduck rules 2026-11-12.2 · LeRobot 0.7.0

入力条件と手順

SO-101 follower、1バス、LeRobot 0.7.0、度単位を確認済み、合成校正ファイル。shoulder_liftを意図的にID 1と申告します。

  1. followerプロファイルと合成ファイルから始めます。
  2. shoulder_liftをID 1にして、duplicate_motor_idとmotor_mappingを確認します。
  3. 校正ファイルを変えずshoulder_liftをID 2へ戻し、報告を比較します。

参考ケースの確認結果

この構成は使用できません

元の申告はブロックされ、commandsReadyはfalseです。

入力と参考結果のJSONを見る
{
  "inputs": {
    "profileId": "so101-follower-v0.7.0",
    "buses": [
      {
        "busId": "follower",
        "profileId": "so101-follower-v0.7.0",
        "port": "/dev/ttyACM0",
        "robotId": "example_follower",
        "version": "0.7.0",
        "useDegrees": true,
        "unitsConfirmed": true,
        "motors": [
          {
            "joint": "shoulder_pan",
            "id": 1,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "shoulder_lift",
            "id": 1,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "elbow_flex",
            "id": 3,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "wrist_flex",
            "id": 4,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "wrist_roll",
            "id": 5,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "gripper",
            "id": 6,
            "model": "sts3215",
            "gearRatio": 345
          }
        ],
        "calibration": {
          "shoulder_pan": {
            "id": 1,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "shoulder_lift": {
            "id": 2,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "elbow_flex": {
            "id": 3,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "wrist_flex": {
            "id": 4,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "wrist_roll": {
            "id": 5,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "gripper": {
            "id": 6,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          }
        }
      }
    ],
    "imuCalibration": null
  },
  "status": "blocked",
  "findings": [
    {
      "code": "duplicate_motor_id",
      "severity": "blocked",
      "fieldPath": "buses.0.motors.1.id",
      "messageKey": "duplicate_motor_id",
      "details": {
        "id": 1,
        "bus": "follower"
      },
      "sourceRef": "lerobot-calibration"
    },
    {
      "code": "motor_mapping",
      "severity": "blocked",
      "fieldPath": "buses.0.motors.1.id",
      "messageKey": "motor_mapping",
      "details": {
        "joint": "shoulder_lift",
        "id": 2
      },
      "sourceRef": "lerobot-calibration"
    }
  ],
  "outputs": {
    "buses": [
      {
        "busId": "follower",
        "profileId": "so101-follower-v0.7.0",
        "role": "follower",
        "family": "so101",
        "version": "0.7.0",
        "port": "/dev/ttyACM0",
        "robotId": "example_follower",
        "declaredMotors": [
          {
            "joint": "shoulder_pan",
            "id": 1,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "shoulder_lift",
            "id": 1,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "elbow_flex",
            "id": 3,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "wrist_flex",
            "id": 4,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "wrist_roll",
            "id": 5,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "gripper",
            "id": 6,
            "model": "sts3215",
            "gearRatio": 345
          }
        ],
        "jointUnits": {
          "shoulder_pan": "degrees",
          "shoulder_lift": "degrees",
          "elbow_flex": "degrees",
          "wrist_flex": "degrees",
          "wrist_roll": "degrees",
          "gripper": "range_0_100"
        },
        "calibrationStatus": "configuration-checked",
        "calibration": {
          "shoulder_pan": {
            "id": 1,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "shoulder_lift": {
            "id": 2,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "elbow_flex": {
            "id": 3,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "wrist_flex": {
            "id": 4,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "wrist_roll": {
            "id": 5,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "gripper": {
            "id": 6,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          }
        }
      }
    ],
    "commandsReady": false,
    "imuStatus": "not-applicable",
    "imuPhysicalPoseVerified": false,
    "physicalChecks": [
      "physical_zero",
      "physical_direction",
      "physical_travel",
      "physical_firmware"
    ],
    "manualChecklist": [
      "manual_single_motor",
      "manual_physical_calibration"
    ]
  }
}

設定を変えて再確認

ID 2へ戻すと両方の申告矛盾がなくなり、修正例に既知の構成矛盾はありません。

既知の構成矛盾なし

変更後の参考JSONを見る
{
  "inputs": {
    "profileId": "so101-follower-v0.7.0",
    "buses": [
      {
        "busId": "follower",
        "profileId": "so101-follower-v0.7.0",
        "port": "/dev/ttyACM0",
        "robotId": "example_follower",
        "version": "0.7.0",
        "useDegrees": true,
        "unitsConfirmed": true,
        "motors": [
          {
            "joint": "shoulder_pan",
            "id": 1,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "shoulder_lift",
            "id": 2,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "elbow_flex",
            "id": 3,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "wrist_flex",
            "id": 4,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "wrist_roll",
            "id": 5,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "gripper",
            "id": 6,
            "model": "sts3215",
            "gearRatio": 345
          }
        ],
        "calibration": {
          "shoulder_pan": {
            "id": 1,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "shoulder_lift": {
            "id": 2,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "elbow_flex": {
            "id": 3,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "wrist_flex": {
            "id": 4,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "wrist_roll": {
            "id": 5,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "gripper": {
            "id": 6,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          }
        }
      }
    ],
    "imuCalibration": null
  },
  "status": "no_known_conflict",
  "findings": [],
  "outputs": {
    "buses": [
      {
        "busId": "follower",
        "profileId": "so101-follower-v0.7.0",
        "role": "follower",
        "family": "so101",
        "version": "0.7.0",
        "port": "/dev/ttyACM0",
        "robotId": "example_follower",
        "declaredMotors": [
          {
            "joint": "shoulder_pan",
            "id": 1,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "shoulder_lift",
            "id": 2,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "elbow_flex",
            "id": 3,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "wrist_flex",
            "id": 4,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "wrist_roll",
            "id": 5,
            "model": "sts3215",
            "gearRatio": 345
          },
          {
            "joint": "gripper",
            "id": 6,
            "model": "sts3215",
            "gearRatio": 345
          }
        ],
        "jointUnits": {
          "shoulder_pan": "degrees",
          "shoulder_lift": "degrees",
          "elbow_flex": "degrees",
          "wrist_flex": "degrees",
          "wrist_roll": "degrees",
          "gripper": "range_0_100"
        },
        "calibrationStatus": "configuration-checked",
        "calibration": {
          "shoulder_pan": {
            "id": 1,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "shoulder_lift": {
            "id": 2,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "elbow_flex": {
            "id": 3,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "wrist_flex": {
            "id": 4,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "wrist_roll": {
            "id": 5,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          },
          "gripper": {
            "id": 6,
            "drive_mode": 0,
            "homing_offset": 0,
            "range_min": 0,
            "range_max": 4095
          }
        }
      }
    ],
    "commandsReady": true,
    "imuStatus": "not-applicable",
    "imuPhysicalPoseVerified": false,
    "physicalChecks": [
      "physical_zero",
      "physical_direction",
      "physical_travel",
      "physical_firmware"
    ],
    "manualChecklist": [
      "manual_single_motor",
      "manual_physical_calibration"
    ]
  }
}

このケースでは確認できないこと

  • 校正ファイルは合成データです。オフセットや範囲を実機に使用しないでください。
  • 申告の編集では実機のIDを走査・変更しません。実機校正が正しいという証明にもなりません。

参考データの作成日:

仕様の出典

以下のリンクには技術資料の原題を記載しています。ケースの前提条件とあわせて、対象バージョンと確認日を確認してください。

  • lerobot-so101410c095eacc0011d998a73383eb94abed2715af0 · 確認日
  • lerobot-calibration410c095eacc0011d998a73383eb94abed2715af0 · 確認日
  • lerobot-units410c095eacc0011d998a73383eb94abed2715af0 · 確認日

IMUファイルはモーターの校正バックアップではない

IMU-v2の形式が正しくても、確認が残るのはなぜですか?

対象バージョン: Microduck rules 2026-11-12.2 · Microduck runtime 4ce3315c86190a632f4d75a2464a4ed31c9af69a · IMU offset format 2

入力条件と手順

Microduck UNO Q / V1.1、申告IDは15個。frameがqmi-policy-body-offset-v2の合成IMU-v2で、配列はゼロ、測定の由来はありません。

  1. 口のID 34を含む15個の実機IDを残します。シミュレーションは14関節です。
  2. synthetic-imu-v2.jsonのversion、frame、acc_offset_ms2、gyro_zero_dpsがIMU用の項目だと確認します。
  3. imu_provenanceを読み、needs_reviewを維持します。合格させるために測定記録を作り足してはいけません。

参考ケースの確認結果

確認が必要

必須項目の構造は有効ですが、測定の由来が不足しています。needs_reviewのままで、imuPhysicalPoseVerifiedはfalseです。

入力と参考結果のJSONを見る
{
  "inputs": {
    "profileId": "microduck-unoq-v1.1",
    "buses": [
      {
        "busId": "microduck-main",
        "profileId": "microduck-unoq-v1.1",
        "port": "",
        "robotId": "microduck",
        "version": "4ce3315c86190a632f4d75a2464a4ed31c9af69a",
        "useDegrees": null,
        "unitsConfirmed": false,
        "motors": [
          {
            "joint": "left_hip_yaw",
            "id": 10,
            "model": "hd1910m",
            "gearRatio": null
          },
          {
            "joint": "left_hip_roll",
            "id": 11,
            "model": "hd1910m",
            "gearRatio": null
          },
          {
            "joint": "left_hip_pitch",
            "id": 12,
            "model": "hd1910m",
            "gearRatio": null
          },
          {
            "joint": "left_knee",
            "id": 13,
            "model": "hd1910m",
            "gearRatio": null
          },
          {
            "joint": "left_ankle",
            "id": 14,
            "model": "hd1910m",
            "gearRatio": null
          },
          {
            "joint": "right_hip_yaw",
            "id": 20,
            "model": "hd1910m",
            "gearRatio": null
          },
          {
            "joint": "right_hip_roll",
            "id": 21,
            "model": "hd1910m",
            "gearRatio": null
          },
          {
            "joint": "right_hip_pitch",
            "id": 22,
            "model": "hd1910m",
            "gearRatio": null
          },
          {
            "joint": "right_knee",
            "id": 23,
            "model": "hd1910m",
            "gearRatio": null
          },
          {
            "joint": "right_ankle",
            "id": 24,
            "model": "hd1910m",
            "gearRatio": null
          },
          {
            "joint": "neck_pitch",
            "id": 30,
            "model": "hd1910m",
            "gearRatio": null
          },
          {
            "joint": "head_pitch",
            "id": 31,
            "model": "hd1910m",
            "gearRatio": null
          },
          {
            "joint": "head_yaw",
            "id": 32,
            "model": "hd1910m",
            "gearRatio": null
          },
          {
            "joint": "head_roll",
            "id": 33,
            "model": "hd1910m",
            "gearRatio": null
          },
          {
            "joint": "mouth",
            "id": 34,
            "model": "hd1910m",
            "gearRatio": null
          }
        ],
        "calibration": null
      }
    ],
    "imuCalibration": {
      "version": 2,
      "frame": "qmi-policy-body-offset-v2",
      "acc_offset_ms2": [
        0,
        0,
        0
      ],
      "gyro_zero_dps": [
        0,
        0,
        0
      ]
    }
  },
  "status": "needs_review",
  "findings": [
    {
      "code": "imu_provenance",
      "severity": "needs_review",
      "fieldPath": "imuCalibration",
      "messageKey": "imu_provenance",
      "details": {},
      "sourceRef": "duck-imu"
    }
  ],
  "outputs": {
    "buses": [
      {
        "busId": "microduck-main",
        "profileId": "microduck-unoq-v1.1",
        "role": "robot",
        "family": "microduck",
        "version": "4ce3315c86190a632f4d75a2464a4ed31c9af69a",
        "port": "",
        "robotId": "microduck",
        "declaredMotors": [
          {
            "joint": "left_hip_yaw",
            "id": 10,
            "model": "hd1910m",
            "gearRatio": null
          },
          {
            "joint": "left_hip_roll",
            "id": 11,
            "model": "hd1910m",
            "gearRatio": null
          },
          {
            "joint": "left_hip_pitch",
            "id": 12,
            "model": "hd1910m",
            "gearRatio": null
          },
          {
            "joint": "left_knee",
            "id": 13,
            "model": "hd1910m",
            "gearRatio": null
          },
          {
            "joint": "left_ankle",
            "id": 14,
            "model": "hd1910m",
            "gearRatio": null
          },
          {
            "joint": "right_hip_yaw",
            "id": 20,
            "model": "hd1910m",
            "gearRatio": null
          },
          {
            "joint": "right_hip_roll",
            "id": 21,
            "model": "hd1910m",
            "gearRatio": null
          },
          {
            "joint": "right_hip_pitch",
            "id": 22,
            "model": "hd1910m",
            "gearRatio": null
          },
          {
            "joint": "right_knee",
            "id": 23,
            "model": "hd1910m",
            "gearRatio": null
          },
          {
            "joint": "right_ankle",
            "id": 24,
            "model": "hd1910m",
            "gearRatio": null
          },
          {
            "joint": "neck_pitch",
            "id": 30,
            "model": "hd1910m",
            "gearRatio": null
          },
          {
            "joint": "head_pitch",
            "id": 31,
            "model": "hd1910m",
            "gearRatio": null
          },
          {
            "joint": "head_yaw",
            "id": 32,
            "model": "hd1910m",
            "gearRatio": null
          },
          {
            "joint": "head_roll",
            "id": 33,
            "model": "hd1910m",
            "gearRatio": null
          },
          {
            "joint": "mouth",
            "id": 34,
            "model": "hd1910m",
            "gearRatio": null
          }
        ],
        "jointUnits": {
          "left_hip_yaw": "encoder_steps",
          "left_hip_roll": "encoder_steps",
          "left_hip_pitch": "encoder_steps",
          "left_knee": "encoder_steps",
          "left_ankle": "encoder_steps",
          "right_hip_yaw": "encoder_steps",
          "right_hip_roll": "encoder_steps",
          "right_hip_pitch": "encoder_steps",
          "right_knee": "encoder_steps",
          "right_ankle": "encoder_steps",
          "neck_pitch": "encoder_steps",
          "head_pitch": "encoder_steps",
          "head_yaw": "encoder_steps",
          "head_roll": "encoder_steps",
          "mouth": "encoder_steps"
        },
        "calibrationStatus": "not-applicable",
        "calibration": null
      }
    ],
    "commandsReady": false,
    "imuStatus": "configuration-checked",
    "imuPhysicalPoseVerified": false,
    "physicalChecks": [
      "physical_zero",
      "physical_direction",
      "physical_travel",
      "physical_firmware",
      "imu_standing",
      "servo_midpoint"
    ],
    "manualChecklist": [
      "manual_declared_ids",
      "manual_midpoint",
      "manual_imu_standing",
      "manual_power"
    ]
  }
}

このケースでは確認できないこと

  • IMU-v2には15モーターの校正は入っておらず、そのバックアップとは呼べません。
  • ゼロ配列は合成値です。静止直立での測定、実機姿勢、15サーボと14模擬関節の実物対応は検証していません。

参考データの作成日:

仕様の出典

以下のリンクには技術資料の原題を記載しています。ケースの前提条件とあわせて、対象バージョンと確認日を確認してください。

  • duck-config4ce3315c86190a632f4d75a2464a4ed31c9af69a · 確認日
  • duck-imu4ce3315c86190a632f4d75a2464a4ed31c9af69a · 確認日
  • duck-midpoint4ce3315c86190a632f4d75a2464a4ed31c9af69a · 確認日
お問い合わせ