准备装机与校准文件
在执行硬件命令前,先检查声明的机器人配置及对应校准格式。电机校准文件与 IMU 校准文件的用途不同。
支持的机器人配置
- SO-101 leader · LeRobot 0.7.0
- SO-101 follower · LeRobot 0.7.0
- Microduck UNO Q / V1.1
收集对应输入
SO-101 需要主臂/从臂、总线、端口、舵机 ID 与减速比信息。请自行确认 use_degrees;校准 JSON 不包含该单位模式。UNO Q 使用 IMU-v2 文件,并单独声明 15 个实机舵机 ID;模拟模型只有 14 个关节。
分三步核对配置
- 选择机器人并添加各条总线,核对关节与 ID 对照;不同总线允许相同 ID。
- 在本地选择对应的电机或 IMU JSON,修正格式、缺失关节和未确认的单位。
- 阅读缺项报告与固定版本说明,再导出备份或命令文本。
报告、备份与命令
可下载项目、检查报告及声明配置备份。支持的命令采用固定官方版本,并按 POSIX 或 PowerShell 正确引用参数;请先审阅,再在外部自行执行。
声明不等于真机验证
页面不会扫描 ID,也不会写入校准。文件结构有效不能证明实机零位、方向或限位正确。UNO Q 的 IMU 校准不是十五舵机校准备份。文件仅在浏览器内检查,不上传。
装机与校准完整案例
这些案例检查声明配置与文件结构。附带的校准文件全部为合成数据,不能用于真实机器人。
离线配置检查不代表真实硬件或安全性已验证。 这些合成案例与上方表单中输入的配置相互独立。导入案例后会重新检查输入,不直接采用已保存的结论。
不同总线可以使用相同 ID
主臂和从臂都使用 ID 1–6,会冲突吗?
适用版本: Microduck rules 2026-11-12.2 · LeRobot 0.7.0
输入条件与操作步骤
LeRobot 0.7.0;leader/follower 分别使用 /dev/ttyACM0 与 /dev/ttyACM1;各自 ID 1–6;useDegrees=true;两份合成校准 JSON。
- 选择两种 SO-101 配置,分别指定总线名称与串口路径,保留各自减速比。
- 载入两份合成文件,并单独确认计划使用角度单位;马达校准 JSON 不包含单位模式。
- 下载参考项目之前,核对两条总线、角度/范围单位与离线结果。
参考检查结果
未发现已知配置冲突
未发现已知配置冲突:不同总线允许相同 ID;这份声明案例的 commandsReady 为 true。
查看输入与参考结果 JSON
{
"inputs": {
"profileId": "so101-leader-v0.7.0",
"buses": [
{
"busId": "leader",
"profileId": "so101-leader-v0.7.0",
"port": "/dev/ttyACM0",
"robotId": "example_leader",
"version": "0.7.0",
"useDegrees": true,
"unitsConfirmed": true,
"motors": [
{
"joint": "shoulder_pan",
"id": 1,
"model": "sts3215",
"gearRatio": 191
},
{
"joint": "shoulder_lift",
"id": 2,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "elbow_flex",
"id": 3,
"model": "sts3215",
"gearRatio": 191
},
{
"joint": "wrist_flex",
"id": 4,
"model": "sts3215",
"gearRatio": 147
},
{
"joint": "wrist_roll",
"id": 5,
"model": "sts3215",
"gearRatio": 147
},
{
"joint": "gripper",
"id": 6,
"model": "sts3215",
"gearRatio": 147
}
],
"calibration": {
"shoulder_pan": {
"id": 1,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"shoulder_lift": {
"id": 2,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"elbow_flex": {
"id": 3,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_flex": {
"id": 4,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_roll": {
"id": 5,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"gripper": {
"id": 6,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
}
}
},
{
"busId": "follower",
"profileId": "so101-follower-v0.7.0",
"port": "/dev/ttyACM1",
"robotId": "example_follower",
"version": "0.7.0",
"useDegrees": true,
"unitsConfirmed": true,
"motors": [
{
"joint": "shoulder_pan",
"id": 1,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "shoulder_lift",
"id": 2,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "elbow_flex",
"id": 3,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_flex",
"id": 4,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_roll",
"id": 5,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "gripper",
"id": 6,
"model": "sts3215",
"gearRatio": 345
}
],
"calibration": {
"shoulder_pan": {
"id": 1,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"shoulder_lift": {
"id": 2,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"elbow_flex": {
"id": 3,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_flex": {
"id": 4,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_roll": {
"id": 5,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"gripper": {
"id": 6,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
}
}
}
],
"imuCalibration": null
},
"status": "no_known_conflict",
"findings": [],
"outputs": {
"buses": [
{
"busId": "leader",
"profileId": "so101-leader-v0.7.0",
"role": "leader",
"family": "so101",
"version": "0.7.0",
"port": "/dev/ttyACM0",
"robotId": "example_leader",
"declaredMotors": [
{
"joint": "shoulder_pan",
"id": 1,
"model": "sts3215",
"gearRatio": 191
},
{
"joint": "shoulder_lift",
"id": 2,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "elbow_flex",
"id": 3,
"model": "sts3215",
"gearRatio": 191
},
{
"joint": "wrist_flex",
"id": 4,
"model": "sts3215",
"gearRatio": 147
},
{
"joint": "wrist_roll",
"id": 5,
"model": "sts3215",
"gearRatio": 147
},
{
"joint": "gripper",
"id": 6,
"model": "sts3215",
"gearRatio": 147
}
],
"jointUnits": {
"shoulder_pan": "degrees",
"shoulder_lift": "degrees",
"elbow_flex": "degrees",
"wrist_flex": "degrees",
"wrist_roll": "degrees",
"gripper": "range_0_100"
},
"calibrationStatus": "configuration-checked",
"calibration": {
"shoulder_pan": {
"id": 1,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"shoulder_lift": {
"id": 2,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"elbow_flex": {
"id": 3,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_flex": {
"id": 4,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_roll": {
"id": 5,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"gripper": {
"id": 6,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
}
}
},
{
"busId": "follower",
"profileId": "so101-follower-v0.7.0",
"role": "follower",
"family": "so101",
"version": "0.7.0",
"port": "/dev/ttyACM1",
"robotId": "example_follower",
"declaredMotors": [
{
"joint": "shoulder_pan",
"id": 1,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "shoulder_lift",
"id": 2,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "elbow_flex",
"id": 3,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_flex",
"id": 4,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_roll",
"id": 5,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "gripper",
"id": 6,
"model": "sts3215",
"gearRatio": 345
}
],
"jointUnits": {
"shoulder_pan": "degrees",
"shoulder_lift": "degrees",
"elbow_flex": "degrees",
"wrist_flex": "degrees",
"wrist_roll": "degrees",
"gripper": "range_0_100"
},
"calibrationStatus": "configuration-checked",
"calibration": {
"shoulder_pan": {
"id": 1,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"shoulder_lift": {
"id": 2,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"elbow_flex": {
"id": 3,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_flex": {
"id": 4,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_roll": {
"id": 5,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"gripper": {
"id": 6,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
}
}
}
],
"commandsReady": true,
"imuStatus": "not-applicable",
"imuPhysicalPoseVerified": false,
"physicalChecks": [
"physical_zero",
"physical_direction",
"physical_travel",
"physical_firmware"
],
"manualChecklist": [
"manual_single_motor",
"manual_physical_calibration"
]
}
}
本案例尚不能证明的事项
- 偏移量与范围是为格式测试构造的值,不是真实备份,绝不能据此操作硬件。
- 串口路径只是示例,单位需另外声明。真实零位、方向和限位仍需按官方流程校准。
参考案例制作日期:
规格资料来源
下列链接保留技术资料的原文标题。请结合案例假设,核对资料版本及核对日期。
- lerobot-calibration410c095eacc0011d998a73383eb94abed2715af0 · 核对日期
- lerobot-so101410c095eacc0011d998a73383eb94abed2715af0 · 核对日期
- lerobot-units410c095eacc0011d998a73383eb94abed2715af0 · 核对日期
- lerobot-leader410c095eacc0011d998a73383eb94abed2715af0 · 核对日期
同一条总线内 ID 重复
shoulder_pan 与 shoulder_lift 都声明为 ID 1,会怎样?
适用版本: Microduck rules 2026-11-12.2 · LeRobot 0.7.0
输入条件与操作步骤
SO-101 follower;单条总线、LeRobot 0.7.0、已确认角度模式与合成校准文件。故意把 shoulder_lift 声明为 ID 1。
- 从 follower 配置及对应合成文件开始。
- 将 shoulder_lift 设为 ID 1,查看 duplicate_motor_id 与 motor_mapping。
- 不改校准文件,只把 shoulder_lift 恢复为 ID 2,比较前后报告。
参考检查结果
此配置不可使用
原声明被阻挡,commandsReady 为 false。
查看输入与参考结果 JSON
{
"inputs": {
"profileId": "so101-follower-v0.7.0",
"buses": [
{
"busId": "follower",
"profileId": "so101-follower-v0.7.0",
"port": "/dev/ttyACM0",
"robotId": "example_follower",
"version": "0.7.0",
"useDegrees": true,
"unitsConfirmed": true,
"motors": [
{
"joint": "shoulder_pan",
"id": 1,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "shoulder_lift",
"id": 1,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "elbow_flex",
"id": 3,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_flex",
"id": 4,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_roll",
"id": 5,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "gripper",
"id": 6,
"model": "sts3215",
"gearRatio": 345
}
],
"calibration": {
"shoulder_pan": {
"id": 1,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"shoulder_lift": {
"id": 2,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"elbow_flex": {
"id": 3,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_flex": {
"id": 4,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_roll": {
"id": 5,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"gripper": {
"id": 6,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
}
}
}
],
"imuCalibration": null
},
"status": "blocked",
"findings": [
{
"code": "duplicate_motor_id",
"severity": "blocked",
"fieldPath": "buses.0.motors.1.id",
"messageKey": "duplicate_motor_id",
"details": {
"id": 1,
"bus": "follower"
},
"sourceRef": "lerobot-calibration"
},
{
"code": "motor_mapping",
"severity": "blocked",
"fieldPath": "buses.0.motors.1.id",
"messageKey": "motor_mapping",
"details": {
"joint": "shoulder_lift",
"id": 2
},
"sourceRef": "lerobot-calibration"
}
],
"outputs": {
"buses": [
{
"busId": "follower",
"profileId": "so101-follower-v0.7.0",
"role": "follower",
"family": "so101",
"version": "0.7.0",
"port": "/dev/ttyACM0",
"robotId": "example_follower",
"declaredMotors": [
{
"joint": "shoulder_pan",
"id": 1,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "shoulder_lift",
"id": 1,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "elbow_flex",
"id": 3,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_flex",
"id": 4,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_roll",
"id": 5,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "gripper",
"id": 6,
"model": "sts3215",
"gearRatio": 345
}
],
"jointUnits": {
"shoulder_pan": "degrees",
"shoulder_lift": "degrees",
"elbow_flex": "degrees",
"wrist_flex": "degrees",
"wrist_roll": "degrees",
"gripper": "range_0_100"
},
"calibrationStatus": "configuration-checked",
"calibration": {
"shoulder_pan": {
"id": 1,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"shoulder_lift": {
"id": 2,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"elbow_flex": {
"id": 3,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_flex": {
"id": 4,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_roll": {
"id": 5,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"gripper": {
"id": 6,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
}
}
}
],
"commandsReady": false,
"imuStatus": "not-applicable",
"imuPhysicalPoseVerified": false,
"physicalChecks": [
"physical_zero",
"physical_direction",
"physical_travel",
"physical_firmware"
],
"manualChecklist": [
"manual_single_motor",
"manual_physical_calibration"
]
}
}
调整后重新检查
恢复 ID 2 后,两项声明冲突消失;修正案例未发现已知配置冲突。
未发现已知配置冲突
查看调整后的参考 JSON
{
"inputs": {
"profileId": "so101-follower-v0.7.0",
"buses": [
{
"busId": "follower",
"profileId": "so101-follower-v0.7.0",
"port": "/dev/ttyACM0",
"robotId": "example_follower",
"version": "0.7.0",
"useDegrees": true,
"unitsConfirmed": true,
"motors": [
{
"joint": "shoulder_pan",
"id": 1,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "shoulder_lift",
"id": 2,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "elbow_flex",
"id": 3,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_flex",
"id": 4,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_roll",
"id": 5,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "gripper",
"id": 6,
"model": "sts3215",
"gearRatio": 345
}
],
"calibration": {
"shoulder_pan": {
"id": 1,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"shoulder_lift": {
"id": 2,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"elbow_flex": {
"id": 3,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_flex": {
"id": 4,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_roll": {
"id": 5,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"gripper": {
"id": 6,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
}
}
}
],
"imuCalibration": null
},
"status": "no_known_conflict",
"findings": [],
"outputs": {
"buses": [
{
"busId": "follower",
"profileId": "so101-follower-v0.7.0",
"role": "follower",
"family": "so101",
"version": "0.7.0",
"port": "/dev/ttyACM0",
"robotId": "example_follower",
"declaredMotors": [
{
"joint": "shoulder_pan",
"id": 1,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "shoulder_lift",
"id": 2,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "elbow_flex",
"id": 3,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_flex",
"id": 4,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_roll",
"id": 5,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "gripper",
"id": 6,
"model": "sts3215",
"gearRatio": 345
}
],
"jointUnits": {
"shoulder_pan": "degrees",
"shoulder_lift": "degrees",
"elbow_flex": "degrees",
"wrist_flex": "degrees",
"wrist_roll": "degrees",
"gripper": "range_0_100"
},
"calibrationStatus": "configuration-checked",
"calibration": {
"shoulder_pan": {
"id": 1,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"shoulder_lift": {
"id": 2,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"elbow_flex": {
"id": 3,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_flex": {
"id": 4,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_roll": {
"id": 5,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"gripper": {
"id": 6,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
}
}
}
],
"commandsReady": true,
"imuStatus": "not-applicable",
"imuPhysicalPoseVerified": false,
"physicalChecks": [
"physical_zero",
"physical_direction",
"physical_travel",
"physical_firmware"
],
"manualChecklist": [
"manual_single_motor",
"manual_physical_calibration"
]
}
}
本案例尚不能证明的事项
- 校准文件是合成数据,不能把其中偏移量或范围用于实物。
- 修改声明不会扫描或改写真实舵机 ID,也不会验证实物校准。
参考案例制作日期:
规格资料来源
下列链接保留技术资料的原文标题。请结合案例假设,核对资料版本及核对日期。
- lerobot-so101410c095eacc0011d998a73383eb94abed2715af0 · 核对日期
- lerobot-calibration410c095eacc0011d998a73383eb94abed2715af0 · 核对日期
- lerobot-units410c095eacc0011d998a73383eb94abed2715af0 · 核对日期
IMU 文件不是舵机校准备份
IMU-v2 结构有效,为什么还需要核对?
适用版本: Microduck rules 2026-11-12.2 · Microduck runtime 4ce3315c86190a632f4d75a2464a4ed31c9af69a · IMU offset format 2
输入条件与操作步骤
机器鸭 UNO Q / V1.1;声明 15 个舵机 ID;合成 IMU-v2 的 frame 为 qmi-policy-body-offset-v2,向量全为零,没有测量来源。
- 保留包括嘴部 ID 34 在内的 15 个实机 ID;模拟模型有 14 个关节。
- 查看 synthetic-imu-v2.json:version、frame、acc_offset_ms2、gyro_zero_dps 属于 IMU 格式。
- 阅读 imu_provenance,保留 needs_review;不要为了通过检查编造测量记录。
参考检查结果
需要进一步核对
必要字段结构有效,但缺少测量来源。报告仍为 needs_review,imuPhysicalPoseVerified 为 false。
查看输入与参考结果 JSON
{
"inputs": {
"profileId": "microduck-unoq-v1.1",
"buses": [
{
"busId": "microduck-main",
"profileId": "microduck-unoq-v1.1",
"port": "",
"robotId": "microduck",
"version": "4ce3315c86190a632f4d75a2464a4ed31c9af69a",
"useDegrees": null,
"unitsConfirmed": false,
"motors": [
{
"joint": "left_hip_yaw",
"id": 10,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "left_hip_roll",
"id": 11,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "left_hip_pitch",
"id": 12,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "left_knee",
"id": 13,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "left_ankle",
"id": 14,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_hip_yaw",
"id": 20,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_hip_roll",
"id": 21,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_hip_pitch",
"id": 22,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_knee",
"id": 23,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_ankle",
"id": 24,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "neck_pitch",
"id": 30,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "head_pitch",
"id": 31,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "head_yaw",
"id": 32,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "head_roll",
"id": 33,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "mouth",
"id": 34,
"model": "hd1910m",
"gearRatio": null
}
],
"calibration": null
}
],
"imuCalibration": {
"version": 2,
"frame": "qmi-policy-body-offset-v2",
"acc_offset_ms2": [
0,
0,
0
],
"gyro_zero_dps": [
0,
0,
0
]
}
},
"status": "needs_review",
"findings": [
{
"code": "imu_provenance",
"severity": "needs_review",
"fieldPath": "imuCalibration",
"messageKey": "imu_provenance",
"details": {},
"sourceRef": "duck-imu"
}
],
"outputs": {
"buses": [
{
"busId": "microduck-main",
"profileId": "microduck-unoq-v1.1",
"role": "robot",
"family": "microduck",
"version": "4ce3315c86190a632f4d75a2464a4ed31c9af69a",
"port": "",
"robotId": "microduck",
"declaredMotors": [
{
"joint": "left_hip_yaw",
"id": 10,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "left_hip_roll",
"id": 11,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "left_hip_pitch",
"id": 12,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "left_knee",
"id": 13,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "left_ankle",
"id": 14,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_hip_yaw",
"id": 20,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_hip_roll",
"id": 21,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_hip_pitch",
"id": 22,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_knee",
"id": 23,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_ankle",
"id": 24,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "neck_pitch",
"id": 30,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "head_pitch",
"id": 31,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "head_yaw",
"id": 32,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "head_roll",
"id": 33,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "mouth",
"id": 34,
"model": "hd1910m",
"gearRatio": null
}
],
"jointUnits": {
"left_hip_yaw": "encoder_steps",
"left_hip_roll": "encoder_steps",
"left_hip_pitch": "encoder_steps",
"left_knee": "encoder_steps",
"left_ankle": "encoder_steps",
"right_hip_yaw": "encoder_steps",
"right_hip_roll": "encoder_steps",
"right_hip_pitch": "encoder_steps",
"right_knee": "encoder_steps",
"right_ankle": "encoder_steps",
"neck_pitch": "encoder_steps",
"head_pitch": "encoder_steps",
"head_yaw": "encoder_steps",
"head_roll": "encoder_steps",
"mouth": "encoder_steps"
},
"calibrationStatus": "not-applicable",
"calibration": null
}
],
"commandsReady": false,
"imuStatus": "configuration-checked",
"imuPhysicalPoseVerified": false,
"physicalChecks": [
"physical_zero",
"physical_direction",
"physical_travel",
"physical_firmware",
"imu_standing",
"servo_midpoint"
],
"manualChecklist": [
"manual_declared_ids",
"manual_midpoint",
"manual_imu_standing",
"manual_power"
]
}
}
本案例尚不能证明的事项
- IMU-v2 不包含 15 个马达的校准,不能把它当成十五舵机校准备份。
- 零向量是合成值;没有验证静止直立采样、真实姿态或 15 舵机与 14 模拟关节的实物对应。
参考案例制作日期:
规格资料来源
下列链接保留技术资料的原文标题。请结合案例假设,核对资料版本及核对日期。
- duck-config4ce3315c86190a632f4d75a2464a4ed31c9af69a · 核对日期
- duck-imu4ce3315c86190a632f4d75a2464a4ed31c9af69a · 核对日期
- duck-midpoint4ce3315c86190a632f4d75a2464a4ed31c9af69a · 核对日期