準備裝機與校正檔案
在執行硬體命令前,先檢查聲明的機器人配置與對應校正格式。馬達校正檔與 IMU 校正檔的用途不同。
支援的機器人配置
- SO-101 leader · LeRobot 0.7.0
- SO-101 follower · LeRobot 0.7.0
- Microduck UNO Q / V1.1
收集對應輸入
SO-101 需要主臂/從臂、匯流排、連接埠、伺服馬達 ID 與減速比資訊。請自行確認 use_degrees;校正 JSON 不包含該單位模式。UNO Q 使用 IMU-v2 檔案,並單獨聲明 15 個實機伺服馬達 ID;模擬模型只有 14 個關節。
分三步核對配置
- 選擇機器人並新增各條匯流排,核對關節與 ID 對照;不同匯流排允許相同 ID。
- 在本機選擇對應的馬達或 IMU JSON,修正格式、缺失關節與未確認的單位。
- 閱讀缺項報告與固定版本說明,再匯出備份或命令文字。
報告、備份與命令
可下載專案、檢查報告與聲明配置備份。支援的命令採用固定官方版本,並按 POSIX 或 PowerShell 正確引用參數;請先審閱,再在外部自行執行。
聲明不等於真機驗證
頁面不會掃描 ID,也不會寫入校正。檔案結構有效不能證明實機零位、方向或限位正確。UNO Q 的 IMU 校正不是十五伺服馬達校正備份。檔案僅在瀏覽器內檢查,不上傳。
裝機與校正完整案例
這些案例檢查宣告設定與檔案結構。附帶的校正檔案都是合成資料,不能用於真實機器人。
離線配置檢查不代表真實硬體或安全性已驗證。 這些合成案例與上方表單輸入的配置相互獨立。匯入案例後會重新檢查輸入,不直接採用已儲存的結論。
不同匯流排可以使用相同 ID
主臂與從臂都使用 ID 1–6,會衝突嗎?
適用版本: Microduck rules 2026-11-12.2 · LeRobot 0.7.0
輸入條件與操作步驟
LeRobot 0.7.0;leader/follower 分別使用 /dev/ttyACM0 與 /dev/ttyACM1;各自 ID 1–6;useDegrees=true;兩份合成校正 JSON。
- 選擇兩種 SO-101 設定,分別指定匯流排名稱與序列埠路徑,保留各自減速比。
- 載入兩份合成檔案,並另外確認計畫使用角度單位;馬達校正 JSON 不包含單位模式。
- 下載參考專案前,核對兩條匯流排、角度/範圍單位與離線結果。
參考檢查結果
未發現已知配置衝突
未發現已知設定衝突:不同匯流排允許相同 ID;此宣告案例的 commandsReady 為 true。
查看輸入與參考結果 JSON
{
"inputs": {
"profileId": "so101-leader-v0.7.0",
"buses": [
{
"busId": "leader",
"profileId": "so101-leader-v0.7.0",
"port": "/dev/ttyACM0",
"robotId": "example_leader",
"version": "0.7.0",
"useDegrees": true,
"unitsConfirmed": true,
"motors": [
{
"joint": "shoulder_pan",
"id": 1,
"model": "sts3215",
"gearRatio": 191
},
{
"joint": "shoulder_lift",
"id": 2,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "elbow_flex",
"id": 3,
"model": "sts3215",
"gearRatio": 191
},
{
"joint": "wrist_flex",
"id": 4,
"model": "sts3215",
"gearRatio": 147
},
{
"joint": "wrist_roll",
"id": 5,
"model": "sts3215",
"gearRatio": 147
},
{
"joint": "gripper",
"id": 6,
"model": "sts3215",
"gearRatio": 147
}
],
"calibration": {
"shoulder_pan": {
"id": 1,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"shoulder_lift": {
"id": 2,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"elbow_flex": {
"id": 3,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_flex": {
"id": 4,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_roll": {
"id": 5,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"gripper": {
"id": 6,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
}
}
},
{
"busId": "follower",
"profileId": "so101-follower-v0.7.0",
"port": "/dev/ttyACM1",
"robotId": "example_follower",
"version": "0.7.0",
"useDegrees": true,
"unitsConfirmed": true,
"motors": [
{
"joint": "shoulder_pan",
"id": 1,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "shoulder_lift",
"id": 2,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "elbow_flex",
"id": 3,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_flex",
"id": 4,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_roll",
"id": 5,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "gripper",
"id": 6,
"model": "sts3215",
"gearRatio": 345
}
],
"calibration": {
"shoulder_pan": {
"id": 1,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"shoulder_lift": {
"id": 2,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"elbow_flex": {
"id": 3,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_flex": {
"id": 4,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_roll": {
"id": 5,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"gripper": {
"id": 6,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
}
}
}
],
"imuCalibration": null
},
"status": "no_known_conflict",
"findings": [],
"outputs": {
"buses": [
{
"busId": "leader",
"profileId": "so101-leader-v0.7.0",
"role": "leader",
"family": "so101",
"version": "0.7.0",
"port": "/dev/ttyACM0",
"robotId": "example_leader",
"declaredMotors": [
{
"joint": "shoulder_pan",
"id": 1,
"model": "sts3215",
"gearRatio": 191
},
{
"joint": "shoulder_lift",
"id": 2,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "elbow_flex",
"id": 3,
"model": "sts3215",
"gearRatio": 191
},
{
"joint": "wrist_flex",
"id": 4,
"model": "sts3215",
"gearRatio": 147
},
{
"joint": "wrist_roll",
"id": 5,
"model": "sts3215",
"gearRatio": 147
},
{
"joint": "gripper",
"id": 6,
"model": "sts3215",
"gearRatio": 147
}
],
"jointUnits": {
"shoulder_pan": "degrees",
"shoulder_lift": "degrees",
"elbow_flex": "degrees",
"wrist_flex": "degrees",
"wrist_roll": "degrees",
"gripper": "range_0_100"
},
"calibrationStatus": "configuration-checked",
"calibration": {
"shoulder_pan": {
"id": 1,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"shoulder_lift": {
"id": 2,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"elbow_flex": {
"id": 3,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_flex": {
"id": 4,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_roll": {
"id": 5,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"gripper": {
"id": 6,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
}
}
},
{
"busId": "follower",
"profileId": "so101-follower-v0.7.0",
"role": "follower",
"family": "so101",
"version": "0.7.0",
"port": "/dev/ttyACM1",
"robotId": "example_follower",
"declaredMotors": [
{
"joint": "shoulder_pan",
"id": 1,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "shoulder_lift",
"id": 2,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "elbow_flex",
"id": 3,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_flex",
"id": 4,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_roll",
"id": 5,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "gripper",
"id": 6,
"model": "sts3215",
"gearRatio": 345
}
],
"jointUnits": {
"shoulder_pan": "degrees",
"shoulder_lift": "degrees",
"elbow_flex": "degrees",
"wrist_flex": "degrees",
"wrist_roll": "degrees",
"gripper": "range_0_100"
},
"calibrationStatus": "configuration-checked",
"calibration": {
"shoulder_pan": {
"id": 1,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"shoulder_lift": {
"id": 2,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"elbow_flex": {
"id": 3,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_flex": {
"id": 4,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_roll": {
"id": 5,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"gripper": {
"id": 6,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
}
}
}
],
"commandsReady": true,
"imuStatus": "not-applicable",
"imuPhysicalPoseVerified": false,
"physicalChecks": [
"physical_zero",
"physical_direction",
"physical_travel",
"physical_firmware"
],
"manualChecklist": [
"manual_single_motor",
"manual_physical_calibration"
]
}
}
本案例尚不能證明的事項
- 偏移量與範圍是為格式測試建立的值,不是實機備份,絕不能據此操作硬體。
- 序列埠路徑只是範例,單位須另外宣告。實際零位、方向與限位仍須依官方流程校正。
參考案例製作日期:
規格資料來源
下列連結保留技術資料的原文標題。請搭配案例假設,核對資料版本與核對日期。
- lerobot-calibration410c095eacc0011d998a73383eb94abed2715af0 · 核對日期
- lerobot-so101410c095eacc0011d998a73383eb94abed2715af0 · 核對日期
- lerobot-units410c095eacc0011d998a73383eb94abed2715af0 · 核對日期
- lerobot-leader410c095eacc0011d998a73383eb94abed2715af0 · 核對日期
同一條匯流排內 ID 重複
shoulder_pan 與 shoulder_lift 都宣告為 ID 1,會怎樣?
適用版本: Microduck rules 2026-11-12.2 · LeRobot 0.7.0
輸入條件與操作步驟
SO-101 follower;單條匯流排、LeRobot 0.7.0、已確認角度模式與合成校正檔。刻意將 shoulder_lift 宣告為 ID 1。
- 從 follower 設定與對應的合成檔案開始。
- 將 shoulder_lift 設為 ID 1,查看 duplicate_motor_id 與 motor_mapping。
- 不改校正檔,只將 shoulder_lift 恢復為 ID 2,比較前後報告。
參考檢查結果
此配置不可使用
原宣告被阻擋,commandsReady 為 false。
查看輸入與參考結果 JSON
{
"inputs": {
"profileId": "so101-follower-v0.7.0",
"buses": [
{
"busId": "follower",
"profileId": "so101-follower-v0.7.0",
"port": "/dev/ttyACM0",
"robotId": "example_follower",
"version": "0.7.0",
"useDegrees": true,
"unitsConfirmed": true,
"motors": [
{
"joint": "shoulder_pan",
"id": 1,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "shoulder_lift",
"id": 1,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "elbow_flex",
"id": 3,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_flex",
"id": 4,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_roll",
"id": 5,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "gripper",
"id": 6,
"model": "sts3215",
"gearRatio": 345
}
],
"calibration": {
"shoulder_pan": {
"id": 1,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"shoulder_lift": {
"id": 2,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"elbow_flex": {
"id": 3,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_flex": {
"id": 4,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_roll": {
"id": 5,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"gripper": {
"id": 6,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
}
}
}
],
"imuCalibration": null
},
"status": "blocked",
"findings": [
{
"code": "duplicate_motor_id",
"severity": "blocked",
"fieldPath": "buses.0.motors.1.id",
"messageKey": "duplicate_motor_id",
"details": {
"id": 1,
"bus": "follower"
},
"sourceRef": "lerobot-calibration"
},
{
"code": "motor_mapping",
"severity": "blocked",
"fieldPath": "buses.0.motors.1.id",
"messageKey": "motor_mapping",
"details": {
"joint": "shoulder_lift",
"id": 2
},
"sourceRef": "lerobot-calibration"
}
],
"outputs": {
"buses": [
{
"busId": "follower",
"profileId": "so101-follower-v0.7.0",
"role": "follower",
"family": "so101",
"version": "0.7.0",
"port": "/dev/ttyACM0",
"robotId": "example_follower",
"declaredMotors": [
{
"joint": "shoulder_pan",
"id": 1,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "shoulder_lift",
"id": 1,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "elbow_flex",
"id": 3,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_flex",
"id": 4,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_roll",
"id": 5,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "gripper",
"id": 6,
"model": "sts3215",
"gearRatio": 345
}
],
"jointUnits": {
"shoulder_pan": "degrees",
"shoulder_lift": "degrees",
"elbow_flex": "degrees",
"wrist_flex": "degrees",
"wrist_roll": "degrees",
"gripper": "range_0_100"
},
"calibrationStatus": "configuration-checked",
"calibration": {
"shoulder_pan": {
"id": 1,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"shoulder_lift": {
"id": 2,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"elbow_flex": {
"id": 3,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_flex": {
"id": 4,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_roll": {
"id": 5,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"gripper": {
"id": 6,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
}
}
}
],
"commandsReady": false,
"imuStatus": "not-applicable",
"imuPhysicalPoseVerified": false,
"physicalChecks": [
"physical_zero",
"physical_direction",
"physical_travel",
"physical_firmware"
],
"manualChecklist": [
"manual_single_motor",
"manual_physical_calibration"
]
}
}
調整後重新檢查
恢復 ID 2 後,兩項宣告衝突消失;修正案例未發現已知設定衝突。
未發現已知配置衝突
查看調整後的參考 JSON
{
"inputs": {
"profileId": "so101-follower-v0.7.0",
"buses": [
{
"busId": "follower",
"profileId": "so101-follower-v0.7.0",
"port": "/dev/ttyACM0",
"robotId": "example_follower",
"version": "0.7.0",
"useDegrees": true,
"unitsConfirmed": true,
"motors": [
{
"joint": "shoulder_pan",
"id": 1,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "shoulder_lift",
"id": 2,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "elbow_flex",
"id": 3,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_flex",
"id": 4,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_roll",
"id": 5,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "gripper",
"id": 6,
"model": "sts3215",
"gearRatio": 345
}
],
"calibration": {
"shoulder_pan": {
"id": 1,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"shoulder_lift": {
"id": 2,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"elbow_flex": {
"id": 3,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_flex": {
"id": 4,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_roll": {
"id": 5,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"gripper": {
"id": 6,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
}
}
}
],
"imuCalibration": null
},
"status": "no_known_conflict",
"findings": [],
"outputs": {
"buses": [
{
"busId": "follower",
"profileId": "so101-follower-v0.7.0",
"role": "follower",
"family": "so101",
"version": "0.7.0",
"port": "/dev/ttyACM0",
"robotId": "example_follower",
"declaredMotors": [
{
"joint": "shoulder_pan",
"id": 1,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "shoulder_lift",
"id": 2,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "elbow_flex",
"id": 3,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_flex",
"id": 4,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "wrist_roll",
"id": 5,
"model": "sts3215",
"gearRatio": 345
},
{
"joint": "gripper",
"id": 6,
"model": "sts3215",
"gearRatio": 345
}
],
"jointUnits": {
"shoulder_pan": "degrees",
"shoulder_lift": "degrees",
"elbow_flex": "degrees",
"wrist_flex": "degrees",
"wrist_roll": "degrees",
"gripper": "range_0_100"
},
"calibrationStatus": "configuration-checked",
"calibration": {
"shoulder_pan": {
"id": 1,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"shoulder_lift": {
"id": 2,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"elbow_flex": {
"id": 3,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_flex": {
"id": 4,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"wrist_roll": {
"id": 5,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
},
"gripper": {
"id": 6,
"drive_mode": 0,
"homing_offset": 0,
"range_min": 0,
"range_max": 4095
}
}
}
],
"commandsReady": true,
"imuStatus": "not-applicable",
"imuPhysicalPoseVerified": false,
"physicalChecks": [
"physical_zero",
"physical_direction",
"physical_travel",
"physical_firmware"
],
"manualChecklist": [
"manual_single_motor",
"manual_physical_calibration"
]
}
}
本案例尚不能證明的事項
- 校正檔是合成資料,不能將其中偏移量或範圍用於實機。
- 修改宣告不會掃描或改寫實際伺服馬達 ID,也不會驗證實機校正。
參考案例製作日期:
規格資料來源
下列連結保留技術資料的原文標題。請搭配案例假設,核對資料版本與核對日期。
- lerobot-so101410c095eacc0011d998a73383eb94abed2715af0 · 核對日期
- lerobot-calibration410c095eacc0011d998a73383eb94abed2715af0 · 核對日期
- lerobot-units410c095eacc0011d998a73383eb94abed2715af0 · 核對日期
IMU 檔案不是伺服馬達校正備份
IMU-v2 結構有效,為什麼還需要核對?
適用版本: Microduck rules 2026-11-12.2 · Microduck runtime 4ce3315c86190a632f4d75a2464a4ed31c9af69a · IMU offset format 2
輸入條件與操作步驟
機器鴨 UNO Q / V1.1;宣告 15 個伺服馬達 ID;合成 IMU-v2 的 frame 為 qmi-policy-body-offset-v2,向量全為零,沒有量測來源。
- 保留嘴部 ID 34 在內的 15 個實機 ID;模擬模型有 14 個關節。
- 查看 synthetic-imu-v2.json:version、frame、acc_offset_ms2、gyro_zero_dps 屬於 IMU 格式。
- 閱讀 imu_provenance,保留 needs_review;不要為了通過檢查編造量測紀錄。
參考檢查結果
需要進一步核對
必要欄位結構有效,但缺少量測來源。報告仍為 needs_review,imuPhysicalPoseVerified 為 false。
查看輸入與參考結果 JSON
{
"inputs": {
"profileId": "microduck-unoq-v1.1",
"buses": [
{
"busId": "microduck-main",
"profileId": "microduck-unoq-v1.1",
"port": "",
"robotId": "microduck",
"version": "4ce3315c86190a632f4d75a2464a4ed31c9af69a",
"useDegrees": null,
"unitsConfirmed": false,
"motors": [
{
"joint": "left_hip_yaw",
"id": 10,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "left_hip_roll",
"id": 11,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "left_hip_pitch",
"id": 12,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "left_knee",
"id": 13,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "left_ankle",
"id": 14,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_hip_yaw",
"id": 20,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_hip_roll",
"id": 21,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_hip_pitch",
"id": 22,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_knee",
"id": 23,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_ankle",
"id": 24,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "neck_pitch",
"id": 30,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "head_pitch",
"id": 31,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "head_yaw",
"id": 32,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "head_roll",
"id": 33,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "mouth",
"id": 34,
"model": "hd1910m",
"gearRatio": null
}
],
"calibration": null
}
],
"imuCalibration": {
"version": 2,
"frame": "qmi-policy-body-offset-v2",
"acc_offset_ms2": [
0,
0,
0
],
"gyro_zero_dps": [
0,
0,
0
]
}
},
"status": "needs_review",
"findings": [
{
"code": "imu_provenance",
"severity": "needs_review",
"fieldPath": "imuCalibration",
"messageKey": "imu_provenance",
"details": {},
"sourceRef": "duck-imu"
}
],
"outputs": {
"buses": [
{
"busId": "microduck-main",
"profileId": "microduck-unoq-v1.1",
"role": "robot",
"family": "microduck",
"version": "4ce3315c86190a632f4d75a2464a4ed31c9af69a",
"port": "",
"robotId": "microduck",
"declaredMotors": [
{
"joint": "left_hip_yaw",
"id": 10,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "left_hip_roll",
"id": 11,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "left_hip_pitch",
"id": 12,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "left_knee",
"id": 13,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "left_ankle",
"id": 14,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_hip_yaw",
"id": 20,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_hip_roll",
"id": 21,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_hip_pitch",
"id": 22,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_knee",
"id": 23,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "right_ankle",
"id": 24,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "neck_pitch",
"id": 30,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "head_pitch",
"id": 31,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "head_yaw",
"id": 32,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "head_roll",
"id": 33,
"model": "hd1910m",
"gearRatio": null
},
{
"joint": "mouth",
"id": 34,
"model": "hd1910m",
"gearRatio": null
}
],
"jointUnits": {
"left_hip_yaw": "encoder_steps",
"left_hip_roll": "encoder_steps",
"left_hip_pitch": "encoder_steps",
"left_knee": "encoder_steps",
"left_ankle": "encoder_steps",
"right_hip_yaw": "encoder_steps",
"right_hip_roll": "encoder_steps",
"right_hip_pitch": "encoder_steps",
"right_knee": "encoder_steps",
"right_ankle": "encoder_steps",
"neck_pitch": "encoder_steps",
"head_pitch": "encoder_steps",
"head_yaw": "encoder_steps",
"head_roll": "encoder_steps",
"mouth": "encoder_steps"
},
"calibrationStatus": "not-applicable",
"calibration": null
}
],
"commandsReady": false,
"imuStatus": "configuration-checked",
"imuPhysicalPoseVerified": false,
"physicalChecks": [
"physical_zero",
"physical_direction",
"physical_travel",
"physical_firmware",
"imu_standing",
"servo_midpoint"
],
"manualChecklist": [
"manual_declared_ids",
"manual_midpoint",
"manual_imu_standing",
"manual_power"
]
}
}
本案例尚不能證明的事項
- IMU-v2 不包含 15 個馬達的校正,不能當成十五顆伺服馬達的校正備份。
- 零向量是合成值;沒有驗證靜止直立取樣、實際姿態或 15 顆伺服馬達與 14 個模擬關節的實物對應。
參考案例製作日期:
規格資料來源
下列連結保留技術資料的原文標題。請搭配案例假設,核對資料版本與核對日期。
- duck-config4ce3315c86190a632f4d75a2464a4ed31c9af69a · 核對日期
- duck-imu4ce3315c86190a632f4d75a2464a4ed31c9af69a · 核對日期
- duck-midpoint4ce3315c86190a632f4d75a2464a4ed31c9af69a · 核對日期