電源経路とBOMを確認する
申告した電気構成を既知の部品データと比較します。電源電圧、変換器の出力、サーボ電流の仕様点は分けて扱います。
ロボットのプリセット
- SO-101 leader
- SO-101 follower
- Microduck UNO Q / V1.1
電圧と電流の根拠を入力
最小・最大電圧はV、電流制限はAで入力します。サーボ数、同時稼働数、電流測定時の電圧も必要です。独自のモーター電流には測定または出典を添えます。不明値は補いません。
電源経路を確認する手順
- プリセットを選び、電源、変換器、制御基板、各サーボ分岐、入力ポートと極性を確認します。
- 経路全体の既知の制限と根拠を入力し、変換器には出力電圧と判明している効率を設定します。
- 待機、申告した連続負荷、全サーボ拘束を比較し、初回通電のチェックリストを読みます。
保存できる資料
プロジェクトとJSON報告、商品・バリアント参照付きのBOM CSVを保存できます。既知の小計は負荷全体ではありません。部品リンクから自動注文したり、価格を変更したりしません。
推定の限界
電流は指定された電圧点のみの値で、補間しません。連続負荷超過はその条件を停止し、拘束電流超過はリスクとして示します。コネクターやヒューズの定格だけで経路全体を認定できません。容量だけでは稼働時間や実物の安全を証明できません。
電源経路を最後まで確認する計算例
宣言した入力からレポートまで、3例をオフラインで追います。電源、変換器、配線上限、基板負荷は合成した申告値で、実測値ではありません。サーボ電流は指定の電圧試験点だけで使用します。
ローカル確認は実機の動作や安全性を保証しません。 ここに示す合成ケースは、上のフォームに入力した値とは別の参考データです。ケースをインポートすると入力から再チェックされ、保存済みの判定はそのまま採用されません。
変換器の前後で電流は変わる
5 Vの負荷電流を12 Vサーボ電流にそのまま足せますか?
対象バージョン: Microduck electrical rules 2026-11-12.2 · Robot profile SO-101 follower / LeRobot 0.7.0 · C018 current specification A/0 2023-07-20, 12 V test point
入力条件と手順
12 V / 4 A、12 V試験点のC018を1個、効率0.8の5 V変換器、出力経路上限2 A、UNO Q USB負荷1 Aを申告します。
- 12 Vサーボ経路と5 Vロジック経路を分けます。
- ロジック負荷を電源側へ換算します:5 × 1 / (12 × 0.8)。
- 各シナリオに入力電流を加え、各経路の上限と比較します。
参考ケースの確認結果
既知の構成矛盾なし
電源側の待機/定格負荷/ストール電流は約0.550833 / 1.420833 / 3.220833 Aです。+10%のストール上限は3.490833 Aで、申告4 Aとの既知の矛盾はありません。
入力と参考結果のJSONを見る
{
"inputs": {
"profileId": "so101-follower-v0.7.0",
"supply": {
"minV": 12,
"maxV": 12,
"continuousA": 4,
"capacityMah": null,
"nominalV": null,
"chemistry": "external-dc",
"polarityConfirmed": true
},
"paths": [
{
"id": "source",
"label": "12 V source and servo branch",
"parentId": null,
"mode": "pass",
"componentIds": [
"waveshare-adapter-a"
],
"limitA": 4,
"limitSource": "Synthetic user declaration for this reference case: 4 A assembled-path limit; not a measurement.",
"assembledVerified": false
},
{
"id": "logic",
"label": "Declared 5 V converter output",
"parentId": "source",
"mode": "regulated",
"componentIds": [],
"outputMinV": 5,
"outputMaxV": 5,
"efficiency": 0.8,
"limitA": 2,
"limitSource": "Synthetic user declaration: 2 A output path and efficiency 0.8; no particular converter or harness verified.",
"assembledVerified": false
}
],
"motors": [
{
"componentId": "sts3215-c018",
"pathId": "source",
"count": 1,
"activeCount": 1,
"performanceV": 12
}
],
"loads": [
{
"id": "uno-q",
"componentId": "uno-q",
"pathId": "logic",
"port": "usb",
"count": 1,
"currentA": 1
}
]
},
"status": "no_known_conflict",
"findings": [],
"outputs": {
"scenarios": {
"idle": {
"complete": true,
"knownSubtotalA": 0.5508333333333334,
"totalA": 0.5508333333333334,
"upperA": 0.5508333333333334,
"paths": [
{
"id": "source",
"complete": true,
"knownSubtotalA": 0.5508333333333334,
"totalA": 0.5508333333333334,
"upperA": 0.5508333333333334
},
{
"id": "logic",
"complete": true,
"knownSubtotalA": 1,
"totalA": 1,
"upperA": 1
}
]
},
"rated": {
"complete": true,
"knownSubtotalA": 1.4208333333333334,
"totalA": 1.4208333333333334,
"upperA": 1.4208333333333334,
"paths": [
{
"id": "source",
"complete": true,
"knownSubtotalA": 1.4208333333333334,
"totalA": 1.4208333333333334,
"upperA": 1.4208333333333334
},
{
"id": "logic",
"complete": true,
"knownSubtotalA": 1,
"totalA": 1,
"upperA": 1
}
]
},
"stall": {
"complete": true,
"knownSubtotalA": 3.2208333333333337,
"totalA": 3.2208333333333337,
"upperA": 3.490833333333334,
"paths": [
{
"id": "source",
"complete": true,
"knownSubtotalA": 3.2208333333333337,
"totalA": 3.2208333333333337,
"upperA": 3.490833333333334
},
{
"id": "logic",
"complete": true,
"knownSubtotalA": 1,
"totalA": 1,
"upperA": 1
}
]
}
},
"paths": [
{
"id": "source",
"label": "12 V source and servo branch",
"parentId": null,
"voltage": {
"minV": 12,
"maxV": 12
},
"knownComponentLimitA": 4,
"assembledPathVerified": false,
"scenarios": {
"idle": {
"complete": true,
"knownSubtotalA": 0.5508333333333334,
"totalA": 0.5508333333333334,
"upperA": 0.5508333333333334
},
"rated": {
"complete": true,
"knownSubtotalA": 1.4208333333333334,
"totalA": 1.4208333333333334,
"upperA": 1.4208333333333334
},
"stall": {
"complete": true,
"knownSubtotalA": 3.2208333333333337,
"totalA": 3.2208333333333337,
"upperA": 3.490833333333334
}
}
},
{
"id": "logic",
"label": "Declared 5 V converter output",
"parentId": "source",
"voltage": {
"minV": 5,
"maxV": 5
},
"knownComponentLimitA": 2,
"assembledPathVerified": false,
"scenarios": {
"idle": {
"complete": true,
"knownSubtotalA": 1,
"totalA": 1,
"upperA": 1
},
"rated": {
"complete": true,
"knownSubtotalA": 1,
"totalA": 1,
"upperA": 1
},
"stall": {
"complete": true,
"knownSubtotalA": 1,
"totalA": 1,
"upperA": 1
}
}
}
],
"bom": [
[
"role",
"path",
"component",
"quantity",
"productId",
"variantId",
"sourceRefs",
"verification"
],
[
"servo",
"source",
"Feetech STS3215-C018",
1,
"lerobot-sts3215",
"sts3215-c018",
"c018-a0",
"offline-configuration; hardware unverified"
],
[
"path component",
"source",
"Waveshare Bus Servo Adapter (A)",
1,
"lerobot-bus-adapter",
"waveshare-bus-adapter-a",
"waveshare-faq",
"component rating only; assembled path unverified"
],
[
"logic load",
"logic",
"Arduino UNO Q",
1,
"uno-q-2gb",
"abx00162",
"unoq-r16;luwu-v11",
"declared load; hardware unverified"
]
],
"runtimeHours": null,
"assumptions": [
{
"fieldPath": "paths.source.limitA",
"value": 4,
"unit": "A",
"evidence": "user-supplied",
"note": "Synthetic user declaration for this reference case: 4 A assembled-path limit; not a measurement."
},
{
"fieldPath": "paths.logic.limitA",
"value": 2,
"unit": "A",
"evidence": "user-supplied",
"note": "Synthetic user declaration: 2 A output path and efficiency 0.8; no particular converter or harness verified."
},
{
"fieldPath": "loads.0.currentA",
"evidence": "user-supplied",
"value": 1,
"unit": "A"
}
],
"checklist": [
"confirm_revision",
"confirm_polarity",
"measure_rails",
"single_servo",
"scan_ids",
"support_robot"
]
}
}
このケースでは確認できないこと
- 上限、効率、負荷、極性確認はすべて例示の申告です。1個のサーボ経路であり、アーム全体の検証ではありません。
- 部品定格は組み上げた経路の定格ではありません。実物の安全性や稼働時間は未検証です。
参考データの作成日:
仕様の出典
以下のリンクには技術資料の原題を記載しています。ケースの前提条件とあわせて、対象バージョンと確認日を確認してください。
- Feetech ST-3215-C018 A/0A/0 2023-07-20, electrical specification p3 · 確認日
- Waveshare Bus Servo Adapter (A) FAQhardware revision not stated · 確認日
- Arduino UNO Q datasheetRevision 16, 2026-10-30 · 確認日
- LeRobot SO-101 setup guideLeRobot v0.7.0 / 410c095eacc0011d998a73383eb94abed2715af0 · 確認日
- Luwu V1.1 PCBA component purchasing BOMedeb42f690907663e0ac2babf7bb858df380a300; component-level procurement ratings · 確認日
連続過負荷は実行を阻止する
申告5 AでC018を6個同時に動かせますか?
対象バージョン: Microduck electrical rules 2026-11-12.2 · Robot profile SO-101 follower / LeRobot 0.7.0 · C018 current specification A/0 2023-07-20, 12 V test point
入力条件と手順
公式12 V電流点、6個すべて動作、電源と経路の上限は合成の5 A申告です。
- 連続需要を計算します:6 × 0.9 = 5.4 A。
- 全ストールを分けて扱います:16.2 A、+10%で17.82 A。
- 動作数の申告だけを2個に変更して再確認します。
参考ケースの確認結果
この構成は使用できません
5.4 Aが5 Aを超えるため、申告した連続シナリオは阻止されます。ストール超過は別の要確認リスクです。
入力と参考結果のJSONを見る
{
"inputs": {
"profileId": "so101-follower-v0.7.0",
"supply": {
"minV": 12,
"maxV": 12,
"continuousA": 5,
"capacityMah": null,
"nominalV": null,
"chemistry": "external-dc",
"polarityConfirmed": true
},
"paths": [
{
"id": "servo",
"label": "12 V adapter and harness",
"parentId": null,
"mode": "pass",
"componentIds": [
"waveshare-adapter-a"
],
"limitA": 5,
"limitSource": "Synthetic user declaration for this case: 5 A source and path; not a measured harness rating.",
"assembledVerified": false
}
],
"motors": [
{
"componentId": "sts3215-c018",
"pathId": "servo",
"count": 6,
"activeCount": 6,
"performanceV": 12
}
],
"loads": []
},
"status": "blocked",
"findings": [
{
"code": "continuous_over_limit",
"severity": "blocked",
"fieldPath": "paths.servo",
"messageKey": "continuous_over_limit",
"details": {
"scenario": "rated",
"current": 5.4,
"limit": 5,
"path": "12 V adapter and harness"
},
"sourceRef": null
},
{
"code": "stall_over_limit",
"severity": "needs_review",
"fieldPath": "paths.servo",
"messageKey": "stall_over_limit",
"details": {
"scenario": "stall",
"current": 17.82,
"limit": 5,
"path": "12 V adapter and harness"
},
"sourceRef": null
},
{
"code": "continuous_over_limit",
"severity": "blocked",
"fieldPath": "supply.continuousA",
"messageKey": "continuous_over_limit",
"details": {
"scenario": "rated",
"current": 5.4,
"limit": 5,
"path": "supply"
},
"sourceRef": null
},
{
"code": "stall_over_limit",
"severity": "needs_review",
"fieldPath": "supply.continuousA",
"messageKey": "stall_over_limit",
"details": {
"scenario": "stall",
"current": 17.82,
"limit": 5,
"path": "supply"
},
"sourceRef": null
}
],
"outputs": {
"scenarios": {
"idle": {
"complete": true,
"knownSubtotalA": 0.18,
"totalA": 0.18,
"upperA": 0.18,
"paths": [
{
"id": "servo",
"complete": true,
"knownSubtotalA": 0.18,
"totalA": 0.18,
"upperA": 0.18
}
]
},
"rated": {
"complete": true,
"knownSubtotalA": 5.4,
"totalA": 5.4,
"upperA": 5.4,
"paths": [
{
"id": "servo",
"complete": true,
"knownSubtotalA": 5.4,
"totalA": 5.4,
"upperA": 5.4
}
]
},
"stall": {
"complete": true,
"knownSubtotalA": 16.200000000000003,
"totalA": 16.200000000000003,
"upperA": 17.820000000000004,
"paths": [
{
"id": "servo",
"complete": true,
"knownSubtotalA": 16.200000000000003,
"totalA": 16.200000000000003,
"upperA": 17.820000000000004
}
]
}
},
"paths": [
{
"id": "servo",
"label": "12 V adapter and harness",
"parentId": null,
"voltage": {
"minV": 12,
"maxV": 12
},
"knownComponentLimitA": 5,
"assembledPathVerified": false,
"scenarios": {
"idle": {
"complete": true,
"knownSubtotalA": 0.18,
"totalA": 0.18,
"upperA": 0.18
},
"rated": {
"complete": true,
"knownSubtotalA": 5.4,
"totalA": 5.4,
"upperA": 5.4
},
"stall": {
"complete": true,
"knownSubtotalA": 16.200000000000003,
"totalA": 16.200000000000003,
"upperA": 17.820000000000004
}
}
}
],
"bom": [
[
"role",
"path",
"component",
"quantity",
"productId",
"variantId",
"sourceRefs",
"verification"
],
[
"servo",
"servo",
"Feetech STS3215-C018",
6,
"lerobot-sts3215",
"sts3215-c018",
"c018-a0",
"offline-configuration; hardware unverified"
],
[
"path component",
"servo",
"Waveshare Bus Servo Adapter (A)",
1,
"lerobot-bus-adapter",
"waveshare-bus-adapter-a",
"waveshare-faq",
"component rating only; assembled path unverified"
]
],
"runtimeHours": null,
"assumptions": [
{
"fieldPath": "paths.servo.limitA",
"value": 5,
"unit": "A",
"evidence": "user-supplied",
"note": "Synthetic user declaration for this case: 5 A source and path; not a measured harness rating."
}
],
"checklist": [
"confirm_revision",
"confirm_polarity",
"measure_rails",
"single_servo",
"scan_ids",
"support_robot"
]
}
}
設定を変えて再確認
動作2個と待機4個で1.92 Aになりますが、全ストールは16.2 A、上限17.82 Aのままです。変更後も要確認です。
確認が必要
変更後の参考JSONを見る
{
"inputs": {
"profileId": "so101-follower-v0.7.0",
"supply": {
"minV": 12,
"maxV": 12,
"continuousA": 5,
"capacityMah": null,
"nominalV": null,
"chemistry": "external-dc",
"polarityConfirmed": true
},
"paths": [
{
"id": "servo",
"label": "12 V adapter and harness",
"parentId": null,
"mode": "pass",
"componentIds": [
"waveshare-adapter-a"
],
"limitA": 5,
"limitSource": "Synthetic user declaration for this case: 5 A source and path; not a measured harness rating.",
"assembledVerified": false
}
],
"motors": [
{
"componentId": "sts3215-c018",
"pathId": "servo",
"count": 6,
"activeCount": 2,
"performanceV": 12
}
],
"loads": []
},
"status": "needs_review",
"findings": [
{
"code": "stall_over_limit",
"severity": "needs_review",
"fieldPath": "paths.servo",
"messageKey": "stall_over_limit",
"details": {
"scenario": "stall",
"current": 17.82,
"limit": 5,
"path": "12 V adapter and harness"
},
"sourceRef": null
},
{
"code": "stall_over_limit",
"severity": "needs_review",
"fieldPath": "supply.continuousA",
"messageKey": "stall_over_limit",
"details": {
"scenario": "stall",
"current": 17.82,
"limit": 5,
"path": "supply"
},
"sourceRef": null
}
],
"outputs": {
"scenarios": {
"idle": {
"complete": true,
"knownSubtotalA": 0.18,
"totalA": 0.18,
"upperA": 0.18,
"paths": [
{
"id": "servo",
"complete": true,
"knownSubtotalA": 0.18,
"totalA": 0.18,
"upperA": 0.18
}
]
},
"rated": {
"complete": true,
"knownSubtotalA": 1.92,
"totalA": 1.92,
"upperA": 1.92,
"paths": [
{
"id": "servo",
"complete": true,
"knownSubtotalA": 1.92,
"totalA": 1.92,
"upperA": 1.92
}
]
},
"stall": {
"complete": true,
"knownSubtotalA": 16.200000000000003,
"totalA": 16.200000000000003,
"upperA": 17.820000000000004,
"paths": [
{
"id": "servo",
"complete": true,
"knownSubtotalA": 16.200000000000003,
"totalA": 16.200000000000003,
"upperA": 17.820000000000004
}
]
}
},
"paths": [
{
"id": "servo",
"label": "12 V adapter and harness",
"parentId": null,
"voltage": {
"minV": 12,
"maxV": 12
},
"knownComponentLimitA": 5,
"assembledPathVerified": false,
"scenarios": {
"idle": {
"complete": true,
"knownSubtotalA": 0.18,
"totalA": 0.18,
"upperA": 0.18
},
"rated": {
"complete": true,
"knownSubtotalA": 1.92,
"totalA": 1.92,
"upperA": 1.92
},
"stall": {
"complete": true,
"knownSubtotalA": 16.200000000000003,
"totalA": 16.200000000000003,
"upperA": 17.820000000000004
}
}
}
],
"bom": [
[
"role",
"path",
"component",
"quantity",
"productId",
"variantId",
"sourceRefs",
"verification"
],
[
"servo",
"servo",
"Feetech STS3215-C018",
6,
"lerobot-sts3215",
"sts3215-c018",
"c018-a0",
"offline-configuration; hardware unverified"
],
[
"path component",
"servo",
"Waveshare Bus Servo Adapter (A)",
1,
"lerobot-bus-adapter",
"waveshare-bus-adapter-a",
"waveshare-faq",
"component rating only; assembled path unverified"
]
],
"runtimeHours": null,
"assumptions": [
{
"fieldPath": "paths.servo.limitA",
"value": 5,
"unit": "A",
"evidence": "user-supplied",
"note": "Synthetic user declaration for this case: 5 A source and path; not a measured harness rating."
}
],
"checklist": [
"confirm_revision",
"confirm_polarity",
"measure_rails",
"single_servo",
"scan_ids",
"support_robot"
]
}
}
このケースでは確認できないこと
- 動作数の申告を減らしても、実機の同時動作や電流は制限されません。
- アダプターの最大5 Aは自動電流制限やハーネス容量の証明ではありません。
参考データの作成日:
仕様の出典
以下のリンクには技術資料の原題を記載しています。ケースの前提条件とあわせて、対象バージョンと確認日を確認してください。
- Feetech ST-3215-C018 A/0A/0 2023-07-20, electrical specification p3 · 確認日
- Waveshare Bus Servo Adapter (A) FAQhardware revision not stated · 確認日
- Arduino UNO Q datasheetRevision 16, 2026-10-30 · 確認日
- LeRobot SO-101 setup guideLeRobot v0.7.0 / 410c095eacc0011d998a73383eb94abed2715af0 · 確認日
- Luwu V1.1 PCBA component purchasing BOMedeb42f690907663e0ac2babf7bb858df380a300; component-level procurement ratings · 確認日
既知の小計は合計ではない
12 Vの電流値を8.4 Vへ流用できますか?
対象バージョン: Microduck electrical rules 2026-11-12.2 · Robot profile SO-101 follower / LeRobot 0.7.0 · C018 current specification A/0 2023-07-20, 12 V test point
入力条件と手順
8.4 V、C018を6個中2個動作、効率0.8の5 V変換器、合成の基板負荷1 Aを申告し、電源と経路の上限を5 Aにします。
- 動作電圧範囲と電流試験点を区別します。
- 8.4 VのC018電流は不明のままとし、補間しません。
- 既知のロジック分だけを計算します:5 × 1 / (8.4 × 0.8)。
参考ケースの確認結果
確認が必要
約0.744048 Aは電源側の既知の小計だけです。サーボ需要、合計、上限、稼働時間は不明です。
入力と参考結果のJSONを見る
{
"inputs": {
"profileId": "so101-follower-v0.7.0",
"supply": {
"minV": 8.4,
"maxV": 8.4,
"continuousA": 5,
"capacityMah": null,
"nominalV": null,
"chemistry": "external-dc",
"polarityConfirmed": true
},
"paths": [
{
"id": "source",
"label": "Declared 8.4 V source and servo branch",
"parentId": null,
"mode": "pass",
"componentIds": [
"waveshare-adapter-a"
],
"limitA": 5,
"limitSource": "Synthetic user declaration: 5 A source/path; no assembled-path test.",
"assembledVerified": false
},
{
"id": "logic",
"label": "Declared 5 V converter output",
"parentId": "source",
"mode": "regulated",
"componentIds": [],
"outputMinV": 5,
"outputMaxV": 5,
"efficiency": 0.8,
"limitA": 2,
"limitSource": "Synthetic user declaration: 2 A output path and efficiency 0.8; no particular converter or harness verified.",
"assembledVerified": false
}
],
"motors": [
{
"componentId": "sts3215-c018",
"pathId": "source",
"count": 6,
"activeCount": 2,
"performanceV": 8.4
}
],
"loads": [
{
"id": "uno-q",
"componentId": "uno-q",
"pathId": "logic",
"port": "usb",
"count": 1,
"currentA": 1
}
]
},
"status": "needs_review",
"findings": [
{
"code": "current_unknown",
"severity": "needs_review",
"fieldPath": "motors.0",
"messageKey": "current_unknown",
"details": {
"component": "Feetech STS3215-C018",
"voltage": 8.4
},
"sourceRef": "c018-a0"
}
],
"outputs": {
"scenarios": {
"idle": {
"complete": false,
"knownSubtotalA": 0.744047619047619,
"totalA": null,
"upperA": null,
"paths": [
{
"id": "source",
"complete": false,
"knownSubtotalA": 0.744047619047619,
"totalA": null,
"upperA": null
},
{
"id": "logic",
"complete": true,
"knownSubtotalA": 1,
"totalA": 1,
"upperA": 1
}
]
},
"rated": {
"complete": false,
"knownSubtotalA": 0.744047619047619,
"totalA": null,
"upperA": null,
"paths": [
{
"id": "source",
"complete": false,
"knownSubtotalA": 0.744047619047619,
"totalA": null,
"upperA": null
},
{
"id": "logic",
"complete": true,
"knownSubtotalA": 1,
"totalA": 1,
"upperA": 1
}
]
},
"stall": {
"complete": false,
"knownSubtotalA": 0.744047619047619,
"totalA": null,
"upperA": null,
"paths": [
{
"id": "source",
"complete": false,
"knownSubtotalA": 0.744047619047619,
"totalA": null,
"upperA": null
},
{
"id": "logic",
"complete": true,
"knownSubtotalA": 1,
"totalA": 1,
"upperA": 1
}
]
}
},
"paths": [
{
"id": "source",
"label": "Declared 8.4 V source and servo branch",
"parentId": null,
"voltage": {
"minV": 8.4,
"maxV": 8.4
},
"knownComponentLimitA": 5,
"assembledPathVerified": false,
"scenarios": {
"idle": {
"complete": false,
"knownSubtotalA": 0.744047619047619,
"totalA": null,
"upperA": null
},
"rated": {
"complete": false,
"knownSubtotalA": 0.744047619047619,
"totalA": null,
"upperA": null
},
"stall": {
"complete": false,
"knownSubtotalA": 0.744047619047619,
"totalA": null,
"upperA": null
}
}
},
{
"id": "logic",
"label": "Declared 5 V converter output",
"parentId": "source",
"voltage": {
"minV": 5,
"maxV": 5
},
"knownComponentLimitA": 2,
"assembledPathVerified": false,
"scenarios": {
"idle": {
"complete": true,
"knownSubtotalA": 1,
"totalA": 1,
"upperA": 1
},
"rated": {
"complete": true,
"knownSubtotalA": 1,
"totalA": 1,
"upperA": 1
},
"stall": {
"complete": true,
"knownSubtotalA": 1,
"totalA": 1,
"upperA": 1
}
}
}
],
"bom": [
[
"role",
"path",
"component",
"quantity",
"productId",
"variantId",
"sourceRefs",
"verification"
],
[
"servo",
"source",
"Feetech STS3215-C018",
6,
"lerobot-sts3215",
"sts3215-c018",
"c018-a0",
"offline-configuration; hardware unverified"
],
[
"path component",
"source",
"Waveshare Bus Servo Adapter (A)",
1,
"lerobot-bus-adapter",
"waveshare-bus-adapter-a",
"waveshare-faq",
"component rating only; assembled path unverified"
],
[
"logic load",
"logic",
"Arduino UNO Q",
1,
"uno-q-2gb",
"abx00162",
"unoq-r16;luwu-v11",
"declared load; hardware unverified"
]
],
"runtimeHours": null,
"assumptions": [
{
"fieldPath": "paths.source.limitA",
"value": 5,
"unit": "A",
"evidence": "user-supplied",
"note": "Synthetic user declaration: 5 A source/path; no assembled-path test."
},
{
"fieldPath": "paths.logic.limitA",
"value": 2,
"unit": "A",
"evidence": "user-supplied",
"note": "Synthetic user declaration: 2 A output path and efficiency 0.8; no particular converter or harness verified."
},
{
"fieldPath": "loads.0.currentA",
"evidence": "user-supplied",
"value": 1,
"unit": "A"
}
],
"checklist": [
"confirm_revision",
"confirm_polarity",
"measure_rails",
"single_servo",
"scan_ids",
"support_robot"
]
}
}
設定を変えて再確認
別の12 V試験点では電源側の定格負荷が約2.440833 Aになります。ストール上限は18.340833 Aなので、変更後も要確認です。
確認が必要
変更後の参考JSONを見る
{
"inputs": {
"profileId": "so101-follower-v0.7.0",
"supply": {
"minV": 12,
"maxV": 12,
"continuousA": 5,
"capacityMah": null,
"nominalV": null,
"chemistry": "external-dc",
"polarityConfirmed": true
},
"paths": [
{
"id": "source",
"label": "Declared 12 V source and servo branch",
"parentId": null,
"mode": "pass",
"componentIds": [
"waveshare-adapter-a"
],
"limitA": 5,
"limitSource": "Synthetic user declaration: 5 A source/path; no assembled-path test.",
"assembledVerified": false
},
{
"id": "logic",
"label": "Declared 5 V converter output",
"parentId": "source",
"mode": "regulated",
"componentIds": [],
"outputMinV": 5,
"outputMaxV": 5,
"efficiency": 0.8,
"limitA": 2,
"limitSource": "Synthetic user declaration: 2 A output path and efficiency 0.8; no particular converter or harness verified.",
"assembledVerified": false
}
],
"motors": [
{
"componentId": "sts3215-c018",
"pathId": "source",
"count": 6,
"activeCount": 2,
"performanceV": 12
}
],
"loads": [
{
"id": "uno-q",
"componentId": "uno-q",
"pathId": "logic",
"port": "usb",
"count": 1,
"currentA": 1
}
]
},
"status": "needs_review",
"findings": [
{
"code": "stall_over_limit",
"severity": "needs_review",
"fieldPath": "paths.source",
"messageKey": "stall_over_limit",
"details": {
"scenario": "stall",
"current": 18.341,
"limit": 5,
"path": "Declared 12 V source and servo branch"
},
"sourceRef": null
},
{
"code": "stall_over_limit",
"severity": "needs_review",
"fieldPath": "supply.continuousA",
"messageKey": "stall_over_limit",
"details": {
"scenario": "stall",
"current": 18.341,
"limit": 5,
"path": "supply"
},
"sourceRef": null
}
],
"outputs": {
"scenarios": {
"idle": {
"complete": true,
"knownSubtotalA": 0.7008333333333334,
"totalA": 0.7008333333333334,
"upperA": 0.7008333333333334,
"paths": [
{
"id": "source",
"complete": true,
"knownSubtotalA": 0.7008333333333334,
"totalA": 0.7008333333333334,
"upperA": 0.7008333333333334
},
{
"id": "logic",
"complete": true,
"knownSubtotalA": 1,
"totalA": 1,
"upperA": 1
}
]
},
"rated": {
"complete": true,
"knownSubtotalA": 2.4408333333333334,
"totalA": 2.4408333333333334,
"upperA": 2.4408333333333334,
"paths": [
{
"id": "source",
"complete": true,
"knownSubtotalA": 2.4408333333333334,
"totalA": 2.4408333333333334,
"upperA": 2.4408333333333334
},
{
"id": "logic",
"complete": true,
"knownSubtotalA": 1,
"totalA": 1,
"upperA": 1
}
]
},
"stall": {
"complete": true,
"knownSubtotalA": 16.720833333333335,
"totalA": 16.720833333333335,
"upperA": 18.340833333333336,
"paths": [
{
"id": "source",
"complete": true,
"knownSubtotalA": 16.720833333333335,
"totalA": 16.720833333333335,
"upperA": 18.340833333333336
},
{
"id": "logic",
"complete": true,
"knownSubtotalA": 1,
"totalA": 1,
"upperA": 1
}
]
}
},
"paths": [
{
"id": "source",
"label": "Declared 12 V source and servo branch",
"parentId": null,
"voltage": {
"minV": 12,
"maxV": 12
},
"knownComponentLimitA": 5,
"assembledPathVerified": false,
"scenarios": {
"idle": {
"complete": true,
"knownSubtotalA": 0.7008333333333334,
"totalA": 0.7008333333333334,
"upperA": 0.7008333333333334
},
"rated": {
"complete": true,
"knownSubtotalA": 2.4408333333333334,
"totalA": 2.4408333333333334,
"upperA": 2.4408333333333334
},
"stall": {
"complete": true,
"knownSubtotalA": 16.720833333333335,
"totalA": 16.720833333333335,
"upperA": 18.340833333333336
}
}
},
{
"id": "logic",
"label": "Declared 5 V converter output",
"parentId": "source",
"voltage": {
"minV": 5,
"maxV": 5
},
"knownComponentLimitA": 2,
"assembledPathVerified": false,
"scenarios": {
"idle": {
"complete": true,
"knownSubtotalA": 1,
"totalA": 1,
"upperA": 1
},
"rated": {
"complete": true,
"knownSubtotalA": 1,
"totalA": 1,
"upperA": 1
},
"stall": {
"complete": true,
"knownSubtotalA": 1,
"totalA": 1,
"upperA": 1
}
}
}
],
"bom": [
[
"role",
"path",
"component",
"quantity",
"productId",
"variantId",
"sourceRefs",
"verification"
],
[
"servo",
"source",
"Feetech STS3215-C018",
6,
"lerobot-sts3215",
"sts3215-c018",
"c018-a0",
"offline-configuration; hardware unverified"
],
[
"path component",
"source",
"Waveshare Bus Servo Adapter (A)",
1,
"lerobot-bus-adapter",
"waveshare-bus-adapter-a",
"waveshare-faq",
"component rating only; assembled path unverified"
],
[
"logic load",
"logic",
"Arduino UNO Q",
1,
"uno-q-2gb",
"abx00162",
"unoq-r16;luwu-v11",
"declared load; hardware unverified"
]
],
"runtimeHours": null,
"assumptions": [
{
"fieldPath": "paths.source.limitA",
"value": 5,
"unit": "A",
"evidence": "user-supplied",
"note": "Synthetic user declaration: 5 A source/path; no assembled-path test."
},
{
"fieldPath": "paths.logic.limitA",
"value": 2,
"unit": "A",
"evidence": "user-supplied",
"note": "Synthetic user declaration: 2 A output path and efficiency 0.8; no particular converter or harness verified."
},
{
"fieldPath": "loads.0.currentA",
"evidence": "user-supplied",
"value": 1,
"unit": "A"
}
],
"checklist": [
"confirm_revision",
"confirm_polarity",
"measure_rails",
"single_servo",
"scan_ids",
"support_robot"
]
}
}
このケースでは確認できないこと
- 12 Vへの設計変更は別の申告シナリオであり、8.4 Vの証拠ではありません。
- このC018例では、C001の5 V時の最低電圧に関する資料の不一致は解消しません。
参考データの作成日:
仕様の出典
以下のリンクには技術資料の原題を記載しています。ケースの前提条件とあわせて、対象バージョンと確認日を確認してください。
- Feetech ST-3215-C018 A/0A/0 2023-07-20, electrical specification p3 · 確認日
- Waveshare Bus Servo Adapter (A) FAQhardware revision not stated · 確認日
- Arduino UNO Q datasheetRevision 16, 2026-10-30 · 確認日
- LeRobot SO-101 setup guideLeRobot v0.7.0 / 410c095eacc0011d998a73383eb94abed2715af0 · 確認日
- Luwu V1.1 PCBA component purchasing BOMedeb42f690907663e0ac2babf7bb858df380a300; component-level procurement ratings · 確認日