Microduck Robot●microduck-robot.com

X42S closed-loop NEMA 17 stepper with FOC driver

Stepper motors

NEMA 17 stepper motor with closed-loop driver board
  • X42S_V1.0 driver board with display, two buttons and labeled pins

Order options

CAN version + 40 mm motor

US$49.00 · each Shipping and taxes included

TTL version + 40 mm motor

US$45.00 · each Shipping and taxes included

TTL driver kit only

US$35.00 · each Shipping and taxes included

A NEMA 17 (42 mm) stepper with a closed-loop FOC driver board on the back: 14-bit encoder, OLED display, and pulse plus TTL serial or CAN control. Also sold as a driver kit for your own motor.

Closed-loop control for a NEMA 17 stepper

The X42S board mounts on the back of a 42 mm stepper and reads the shaft with a 14-bit magnetic encoder, so the motor does not lose steps. It accepts step/direction pulses like an ordinary driver and can also be commanded over TTL serial (A version) or CAN (C version).

  • Supply: 10–29 V DC, at least 3 A; up to 5 A motor current.
  • Modes: torque, speed and position control, synchronous commands for several motors, trapezoidal acceleration, homing and limits.
  • Speed: 0.1 to over 3000 rpm; step pulses up to 300 kHz.
  • Protocols: the maker's own protocol, Modbus and DMX512; firmware can be updated over USB-to-RS485 or CAN.
  • On the board: an OLED display for angle, error and pulse count, and two buttons.

In the box

Motor options: the board fitted to a 40 mm motor, a 3 cm motor cable and a 50 cm 8-pin cable. Driver kit: the board, four M3 × 40 screws, four spacers, a 5 × 2.5 mm radial magnet for the motor shaft, a plastic housing, a motor cable and an 8-pin cable. The kit needs a motor with a rear shaft for the magnet.

Specifications
Supply
10–29 V DC, 3 A or more
Encoder
14-bit magnetic
Control
Pulse/direction plus TTL serial or CAN; torque, speed and position modes
Speed
0.1 to over 3000 rpm; pulses up to 300 kHz
Current
Up to 5 A
Motor
40 mm NEMA 17 in the motor options
Included
Board on motor, motor cable, 8-pin cable (motor options)
Compatibility checks
  • Choose the CAN version for chaining several axes, TTL for a single microcontroller.
  • The driver kit includes a radial magnet that must be fitted to your motor's shaft.

Robot motors and reducers →

BEFORE YOU ORDER

Get the right part the first time

Start with the part you are replacing, then compare the model, connections and package below.

What should I check before choosing this part?
  • Choose the CAN version for chaining several axes, TTL for a single microcontroller.
  • The driver kit includes a radial magnet that must be fitted to your motor's shaft.
Which version or package should I select?
  • CAN version + 40 mm motor · each
  • TTL version + 40 mm motor · each
  • TTL driver kit only · each
Compare order options →
Which specifications should I compare?
Supply
10–29 V DC, 3 A or more
Encoder
14-bit magnetic
Control
Pulse/direction plus TTL serial or CAN; torque, speed and position modes
Speed
0.1 to over 3000 rpm; pulses up to 300 kHz
Current
Up to 5 A
Motor
40 mm NEMA 17 in the motor options
Included
Board on motor, motor cable, 8-pin cable (motor options)
Compare order options ↑

Build notes & feedback

Used this part in a build? Tell us your exact model, selected option and what did or did not fit.

Share your experience ↗
Contact us