Microduck Robot●microduck-robot.com

Robot duck wiring guide: UNO Q, expansion board, battery and servo bus

A reference diagram for the UNO Q robot, not confirmation of your assembled wiring. Verify the actual board revision, battery, connector orientation and power path before connecting hardware.

Wiring diagram

Arduino UNO Q · Expansion board V1.1 · Battery · Servo ports Expansion board V1.1 Battery8.4 V BOM label · pack unconfirmed Charger8.4 V · 5.5 × 2.1 mm plug Battery input CN1XH2.54, 2 pins Charge socket DC1switch OFF to charge Reverse protection + switchU2 + Q1 · SW1 5 V buck converterU3 TPS566238 3.3 V regulatorAMS1117-3.3 IMUQMI8658A · I²C Half-duplex bufferSN74LVC1G125 / 126 Servo portsP1S · V · GP2S · V · GP3S · V · GComponent ratings only Arduino UNO Qstacked on the board powerI²C D1 TXD0 RX Left leg · 10–141011121314Right leg · 20–242021222324Neck and head · 30–343031323334 mouth
Tap a block to see what it does. Swipe sideways on a small screen.

What connects to what

The robot has three electrical parts: the Arduino UNO Q, the expansion board stacked on it, and the battery. Everything else, all 15 servos, hangs off the expansion board on one serial bus.

The diagram shows the intended battery, 5 V and 3.3 V paths. Actual battery voltage and the assembled board supply route must be verified for the matching revision; component names alone do not prove a loaded power path.

Power: battery, switch and charging

The purchasing BOM lists an 18650 / 8.4 V pack, capacity over 2,500 mAh, discharge over 3C and an XH2.54 connector. Chemistry, cell arrangement, BMS and polarity are not established; confirm the actual pack.

The BOM lists an 8.4 V charger with a 5.5 × 2.1 mm plug. This alone does not prove compatibility with the actual pack. Confirm the charger, charging current and polarity; use the documented switch-OFF procedure only for a confirmed matching pack.

The V1.1 purchasing workbook marks CN1 2 A, P1–P3 4 A, F1–F3 3 A hold and SW1 3 A. These are component markings, not an assembled-path rating. Do not add branch fuse capacities; wiring, traces and temperature rise remain unverified.

RailWhere it comes fromFeedsCheck at
BAT · 8.4 V BOM label · pack unconfirmedBattery, through the protection and SW1Servo ports P1–P3 (pin V)BAT / GND test points, BAT LED
5 VBuck converter U3UNO Q and board logic5V / GND test points, 5 V LED
3.3 VRegulator AMS1117-3.3 from 5 VIMU and bus buffer3V3 / GND test points

The servo bus

The three servo ports P1, P2 and P3 are 2.0 mm 3-pin connectors printed S, V, G. On V1.1 pin 1 is signal, pin 2 the battery voltage and pin 3 ground, the same order as the servo's own connector: 1 signal, 2 VCC, 3 GND. The servo cables are AMP 2.0 mm 3-pin; all three wires can be black, so go by the pin numbers, not the colour.

All three ports carry the same bus: the runtime reaches all 15 IDs on one serial port. Which chain goes into which port does not matter for communication. Putting one chain on each port spreads the current over the three fuses.

The bus is half-duplex TTL serial at 1 Mbit/s, 8 data bits, no parity, 1 stop bit. Each servo needs its own ID before it goes on the bus: two servos with the same ID both obey the same write.

IDsJointsChain
10–14Left leg, hip to ankleone port
20–24Right leg, hip to ankleone port
30–33Neck and headone port, together with the mouth
34Mouthend of the neck and head chain

The UNO Q side

The expansion board plugs onto the UNO Q's UNO headers, so there are no loose wires between the two. The microcontroller drives the servos on Serial1, which is D1 (TX) and D0 (RX) on the header, and reads the IMU over I²C. Leave D0 and D1 free for the servo bus.

UNO Q has separate voltage domains. Check the official full pinout: VIN is 7–24 V, USB-C is 5 V up to 3 A, and 5V_SYS is an output. These are different interfaces; do not treat every header as a 3.3 V or power-input pin.

Boards made before V1.1

Board age alone does not establish its connector pinout. Compare the exact board revision and mating view with the matching source files; with power disconnected, verify signal, supply and ground before using any old-board crossover advice.

If you have an older board, measure it with the power off. If it matches the old order, swap the signal and ground terminals at the board end of each cable only, or use a crossover adapter, keep power on pin 2, and label those cables for the old board.

First power-on checklist

  1. With all power disconnected, exclude a sustained short on BAT/GND, 5V/GND and 3V3/GND. A brief continuity beep while capacitors charge is not by itself proof of a short; use appropriate resistance and circuit checks.
  2. Plug in the battery with the switch OFF. Check the polarity marks first.
  3. Only after confirming the actual pack and wiring, power the board without servos and measure each rail against the matching schematic. Do not assume a 7.4–8.4 V battery from the purchasing label alone.
  4. Switch off, connect one confirmed-compatible servo, then use the robot runtime or a physical adapter to ping it. The website bus tool simulates replies and does not connect to hardware.
  5. Give every servo its ID one at a time, then connect the three chains. Scan: all 15 IDs must answer.
  6. Support the robot so the legs hang free before you enable torque or calibrate. A servo that is blocked draws its stall current, about 2 A at 7.4 V, so avoid stalling them.

Board components used in this guide

PartComponentWhat it does
CN1XH2.54, 2 pinsBattery input
DC15.5 × 2.1 mm DC socketCharger input
SW1Slide switchMain power
U2 + Q1LM74502 + N-channel MOSFETReverse-polarity protection
U3 + L1TPS566238 + 2.7 µH inductor5 V buck converter
Q3AMS1117-3.33.3 V regulator
U1QMI8658A6-axis IMU
SN1, SN2SN74LVC1G126, SN74LVC1G125Half-duplex bus buffer
P1–P32.0 mm 3-pin, right-angleServo ports
F1–F3Resettable fuse, 3 A holdOne per servo port
D1, D2, D5SMBJ9.0A TVS diodeSurge protection, one per port

Questions

What battery does the robot duck use?

The purchasing BOM lists an 18650 / 8.4 V pack, capacity over 2,500 mAh, discharge over 3C and an XH2.54 connector. Chemistry, cell arrangement, BMS and polarity are not established; confirm the actual pack. The BOM lists an 8.4 V charger with a 5.5 × 2.1 mm plug. This alone does not prove compatibility with the actual pack. Confirm the charger, charging current and polarity; use the documented switch-OFF procedure only for a confirmed matching pack.

Which UNO Q pins does the servo bus use?

Serial1, which is D1 (TX) and D0 (RX) on the UNO header, at 1 Mbit/s. The expansion board's buffer joins TX and RX into the single signal wire of the servo bus.

Does it matter which servo port each chain goes into?

Not for communication: the three ports share one bus, and each servo is addressed by its ID. One chain per port spreads the current over the three fuses. The V1.1 purchasing workbook marks CN1 2 A, P1–P3 4 A, F1–F3 3 A hold and SW1 3 A. These are component markings, not an assembled-path rating. Do not add branch fuse capacities; wiring, traces and temperature rise remain unverified.

Do I need a separate buck converter?

The diagram shows the intended battery, 5 V and 3.3 V paths. Actual battery voltage and the assembled board supply route must be verified for the matching revision; component names alone do not prove a loaded power path.

Source snapshot: Luwu hardware commit edeb42f (2026-11-11), its V1.1 purchasing workbook, the maintained HD-1910-C001 supplier transcription, and Arduino UNO Q datasheet revision 16. Component records and a diagram are not a completed board bring-up or whole-robot load test.

Project sources

Assembly guide → Bus servo command tool →

Contact us