Microduck Robot●microduck-robot.com

SimpleFOC starter parts: driver, 2804 motor and encoder

Motor drivers and adapters

SimpleFOC driver board, 2804 gimbal motor and encoder board
  • DRV8316 driver board with green screw terminals and a small heatsink

Order options

SimpleFOC Mini V2 driver

US$15.00 · each Shipping and taxes included

2804 motor + MT6701 encoder

US$29.00 · each Shipping and taxes included

2804 motor + AS5600 encoder

US$29.00 · each Shipping and taxes included

MT6701 encoder module

US$9.00 · each Shipping and taxes included

Parts for learning field-oriented control with the SimpleFOC library: the SimpleFOC Mini V2 driver, a 2804 hollow-shaft gimbal motor with an MT6701 or AS5600 encoder, and a separate MT6701 encoder module.

Parts for learning FOC

These components for learning field-oriented control with SimpleFOC are sold separately: a driver, a small gimbal motor with its encoder already fitted, or a standalone encoder module for your own motor. Check the selected option for its contents.

  • SimpleFOC Mini V2: TI DRV8316 driver, 8–35 V input, 3 A continuous and 8 A peak, protection against over-current, under-voltage and over-temperature, 27 × 27 mm, pin-compatible with the first version.
  • 2804 motor: hollow-shaft outer-rotor BLDC with an aluminium housing, 7.4–16 V (12 V typical), about 0.03 N·m, Ø34.5 × 15 mm, shipped with its encoder board mounted.
  • MT6701 encoder: 14-bit, with ABZ, I2C, SSI and PWM outputs; the separate module comes with a radial magnet, a cable and brass standoffs.
  • AS5600 encoder: 12-bit over I2C.

You need a microcontroller with three independent PWM outputs, such as an ESP32, STM32 or Arduino board, and a 12 V supply for the 2804. Voltage-mode FOC works with SimpleFOC as is; current control on this driver needs extra code.

Specifications
SimpleFOC Mini V2
DRV8316 driver, 8–35 V, 3 A continuous, 8 A peak, 27 × 27 mm
2804 motor
Hollow-shaft outer-rotor BLDC, 7.4–16 V, about 0.03 N·m, Ø34.5 × 15 mm
MT6701 encoder
14-bit; ABZ, I2C, SSI or PWM
AS5600 encoder
12-bit, I2C
Controllers
Works with ESP32, STM32 and Arduino boards through SimpleFOC
Compatibility checks
  • Voltage-mode FOC works with SimpleFOC as is; current control on this driver needs extra code.
  • Buy one driver for each motor.

Robot motors and reducers →

Technical references

BEFORE YOU ORDER

Get the right part the first time

Start with the part you are replacing, then compare the model, connections and package below.

What should I check before choosing this part?
  • Voltage-mode FOC works with SimpleFOC as is; current control on this driver needs extra code.
  • Buy one driver for each motor.
Which version or package should I select?
  • SimpleFOC Mini V2 driver · each
  • 2804 motor + MT6701 encoder · each
  • 2804 motor + AS5600 encoder · each
  • MT6701 encoder module · each
Compare order options →
Which specifications should I compare?
SimpleFOC Mini V2
DRV8316 driver, 8–35 V, 3 A continuous, 8 A peak, 27 × 27 mm
2804 motor
Hollow-shaft outer-rotor BLDC, 7.4–16 V, about 0.03 N·m, Ø34.5 × 15 mm
MT6701 encoder
14-bit; ABZ, I2C, SSI or PWM
AS5600 encoder
12-bit, I2C
Controllers
Works with ESP32, STM32 and Arduino boards through SimpleFOC
Compare order options ↑

Build notes & feedback

Used this part in a build? Tell us your exact model, selected option and what did or did not fit.

Share your experience ↗
Contact us